Midshaft Won't Expand?

I’m wondering if I have a possible penis injury. Above the curve I have at the base, under the circumcision scar, I don’t have much expansion there. Sometime when I go to piss, my flaccid is filled up at my base and above my circumcision scar. Underneath looks lifeless and dark, while the rest of my penis is red. It’s even more apparent when I pump. It looks like )(

After pumping and I go to flaccid, my penis is flushed red and my midshaft is dark and not expanded. I’m 5.75” MEG and 6” BEG, but when I expand it goes to 5 7/8” MEG and 6 3/4” BEG (no fluid). Im thinking it took place when i did Slow Squash Jelqs a while back and i mightve developed plaque. I doubt it because i can stretch and get erect without any pain.

Although it fills ups with blood slower than the rest of my penis, it looks normal while flaccid or erect. This isn’t new, it’s been like this for years now. I’m bringing it up because I feel like it’s holding back expansion in the pump.

Has anyone experienced this issue or is currently going through it?

I can say that my mid-shaft also does not expand on the left side. If it has gone on for years then that points to a malformed CC. PE may or may not correct this and could be a cause however if you have had these symptoms for years regarding mid-shaft inflation I doubt it was PE related.

I know that I have similar problems and that they are a driving goal for me to correct. I am unsure exactly how much of it can be corrected.

Today I did another session and got base girth to 7”. Again, my midshaft was still at 5 7/8”. I have never been able to get larger shaft girth past 5 7/8” despite un pumped girth being 5.75”. I literally get 1/8” expansion, compared to my base getting 1” expansion without any fluid. Maybe my CC is maxed out and my CS need growth? My CS is small at my midshaft, but large at the base. When I pump, my CC at the base gets larger

I am of the belief that higher up may not be fully formed or has a funny shape. This I believe is my own problem. Also, this could be from any number of reasons, congenital being a primary one. But scar tissue or a plaque formation could inhibit expansion in theory. Without analysis your instances of non-uniform expansion are unknowable if they haven’t been all of your life.

Mine have been all of my life and I’m pretty sure it’s based on how I developed from a young age. However, that is only theory based on the trend having been always true.

I’m sure it was from PE. I wasnt born this way. It’s probably plaque build up. I just made this topic wondering if I could possibly get tips on what to do, but nobody has the answers.

I’m not sure if plaque is the right word but it definitely sounds like that area of your shaft is tougher and takes more force to expand it. It’s good that it is the right size when fully erect, and the problem is mainly with low inflation force (ie semi erect). That’s a good sign that it can be de-toughened and will come good eventually.

You can try massaging that tough shaft area a few times a day until it starts to soften up and feels the same as the softer base shaft internal area. Massaging will give you good feedback on the progress of softening it up, you should feel improvements each day. Keep the massaging light and avoid pain, it should feel like warming, itching, loosening etc, not discomfort.

It’s probably caused by pumping, that end shaft area gets more pumping trauma than the base shaft area. So keep your pumping to lower force levels and take longer to ramp up to your main vacuum level. And avoid that temptation to spike the vacuum right up to get it expanded, that’s a major cause of toughness. It’s ok to do cyclic or dynamic pumping, just keep the vacuum force always within a sensible range and avoid any high peak forces (or unusual force levels) that cause immediate discomfort.

Also if you are pumping in a tube that is too large, with too much vacuum force, that will cause it for sure. The correct tube size should support your end shaft girth just a bit bigger than normal erect size.

I finally got it to expand by 1/16” with my pumped size. So now my un pumped size is also 1/16” larger. I just upped the vacuum to the 8.5” Mark on the x40, which for me right now is maxed vacuum. Until, it’s not anymore.

I figured something had to change because I went from 5.5 to 5.75” over time while having this issue. On my way to 6” now.