Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

My LA Pump Broke

My LA Pump Broke

Yesterday, when I started pumping, I noticed that the pressure did not stay. I would pump up to about 2 or 3 HG and leave it there for a few seconds. Then I noticed the pressure would drop back to 1 HG and then to 0. I could also feel the pressure leaving the cylinder and watch my penis slowly shrink back down. I know I am getting a good seal. I even shaved again to make sure. I have only used the pump for 2 weeks and it worked perfectly. I am doing nothing different, but all of a sudden the pressure won’t stay. Is it broken or is there something I could be doing wrong?

This is a brass pump, right?

The quick disconnect on the top of the tube came loose on me 2x’s. Try that. If that isnt it, pull of your hose off the pump and put your finger over the hole, if it pumps and hold pressure, its your hose, if not, its your pump. Good luck.


All information here is from my cow Bessy. The opinions and posts are hers and not mine. I just do the typing for her because we all know cows cant type. Fieldmouse :iws:

BTW, the fitting on top of the tube, just snug up. If you overtighten it, the threads might strip.


All information here is from my cow Bessy. The opinions and posts are hers and not mine. I just do the typing for her because we all know cows cant type. Fieldmouse :iws:

Originally Posted by fieldmouse
The quick disconnect on the top of the tube came loose on me 2x’s. Try that. If that isnt it, pull of your hose off the pump and put your finger over the hole, if it pumps and hold pressure, its your hose, if not, its your pump. Good luck.

Word. What he said.


All information here is from my cow Bessy. The opinions and posts are hers and not mine. I just do the typing for her because we all know cows cant type. Fieldmouse :iws:

In addition to the O-ring on the female connector, wrap the threads with plumbers Teflon tape and then screw it in for a leak proof seal.

Also make sure the male connector fully clicks in to the female connector.

I doubt your pump is broken.

I disconnected the pump form the cylinder and put my finger over the small hole of the pump and was able to pump and hold pressure with it. This means it must be my cylinder. It seems like every thing is snug when I connect the two however. What did you mean, gprent, when you said wrap the O-ring and threads with tape. Is this the part of the pump that screws into the cylinder? Air must be leaking through the top where the cylinder connects to the pump even though I don’t see how this would be possible.

Plumbers Teflon tape prevents leaks on threaded fittings. Take out the female connector and wrap the threads about 3 times around with plumbers Teflon tape and screw it back in. You can find the Teflon tape at Home Depot or Walmart.

Originally Posted by gprent101
Plumbers Teflon tape prevents leaks on threaded fittings. Take out the female connector and wrap the threads about 3 times around with plumbers Teflon tape and screw it back in. You can find the Teflon tape at Home Depot or Walmart.

What he said.


All information here is from my cow Bessy. The opinions and posts are hers and not mine. I just do the typing for her because we all know cows cant type. Fieldmouse :iws:

Top
Similar Threads 
ThreadStarterForumRepliesLast Post
Dr. Kaplan's hand pumpjallenPenis Pumps807-13-2008 09:41 AM
Attention electric pump users ? Which is the best electric pump ?etherosPenis Pumps409-22-2005 05:47 PM
Benefits of electric pump over manual pump?romeo1Penis Pumps211-26-2004 01:53 PM
Mityvac pump diy pumpiknowicanPenis Pumps711-01-2004 05:05 AM
Broke my LA pump, where to buy cheap replacement or parts?a529612Penis Pumps610-16-2004 07:48 PM

All times are GMT. The time now is 12:06 AM.