Keep packing the 2" or keep using the 2.25"?

I’ve been making good progress. and because of the inspiration and support from this site, I’ve worked up to packing the 2” tube about 1 year ago—and it really smooshes my glans when my whole penis is packed. So I’ve been mainly using the 2.25” and my glans (which is much bigger then my shaft) is getting close to touching the wall of the 2.25”. At this point I’d rather have more length than girth. I’ve been using the penimaster pro together with pumping, and am wondering if using the 2” packed actually does help the penis grow longer? I know that is a common consensus…

In the big plan I would use the slightly bigger tube and reassess the pressure, it will help you’re veins and ligaments to stretch in more than 1 way.

In my experience is that it’s not an issue that the glans is touching the way, and my glans and part of shaft are the same size. I prefer it for consistency.

When changing your tube be careful with the pressure and liquid buildup, reduce time and/or pressure temporarily.

With high pressure pumping it would keep the smaller one, or like I said reduce/retrain the pressure with the bigger tube.

I didn’t upgrade my 2” cylinder until when I release the vacuum and had to wait or really pull to get out.

I vote for using the larger cylinder. When you tightly pack a cylinder, it makes it difficult for your erection to slide up the walls of the cylinder to provide full length extension.

I’m going to go against the grain since you’re specifically looking for length. I would make sure you are very well lubed and stick with the smaller tube. I would probably spend 2 days in smaller tube 3rd day use the larger then rest one day and repeat. Again be sure to lube very well or you won’t be able to stretch up the tube. The day in the larger tube I would think of as active rest and use lower pressure.

Get a size in-between.

LeLuv Vacuum Cylinder for Enhancement Pumps Seamless Untapered Medical-Grade Clear Acrylic with Measurement Marks and Locking Fitting 2.125 inch x 9 inch https://www.ama … /dp/B00KKW2E5W/

I will say get a thicker/wider cylinder. The glans might be getting too thick and prevent from getting more length inside the tube. Just a thought.

I am in same boat, the 2” smashes my penis but I get 8”+ in it…..so bought a 2.125…and yes my glands smash against this one too…but all you have to do as others have said is put a little lubricant on the penis especially the head….good luck!

PS: whats interesting is I’ll get 8” with the 2.0—move to the 2.125” and it’s more like 7.75” then —-

Hi I know this is the old message, but can anyone tell me is this just the cylinder, or does it include pump?

I was going to order a thickwall starter but it only comes with 9" length and would like larger.

It is just the cylinder. I have this one.

Amazon sells several vac pumps that you can get. Here is just one example, which is a brake bleeder kit and which has the pistol style vac pump, hoses and a fluid trap which can be used if you want to try pumping with water. The other fittings in the kit are not needed for PE purposes.

https://www.ama … /dp/B085TGJJJF/

Ok, so would this fit the leluv cylinder above? Sorry I’m new to pumping and have only used a very basic pump

You will also need a 1/4” male quick disconnect coupler for the pump hose. This is a set of both male and female. If you search a little more you should be able to find a male only for around $8-$10.

https://www.ama … /dp/B074Q3L2LH/

Thank you so much, I went ahead and ordered cylinder and pump, I’m gona order a coupler now. Would this do
https://www.ama … /dp/B07B67P3SX/

Sorry to keep asking just wana make sure I don’t order something that doesnt fit.

No, that is a threaded fitting. You need a 1/4” male quick disconnect fitting.

Might just order the two pack. At some point you will likely need to replace the female on the cylinder. As they are plastic it is not to difficult to drop the cylinder and break the fitting.