Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Pumping without a gauge

1234

Hi iv you st to pump with out a gauge but after so I’m I think I yoused to mutch presher and my forskin blow up like a ballon

Is it possible to water pump and still use a gauge?


What doesn't kill you makes you longer.

Thanks. The word ‘hydraulic’ wasn’t in any of my searches. Thanks again.


What doesn't kill you makes you longer.

:up:

I have to say, I’ve been pumping (on and off) for 15 years, with no gauge. My Current pump had a gauge which I removed to make it less cumbersome. If I can take more suction, and it feels ok, why not go for it. Seeing a number might do more harm than good, trying to attain that level, before your cock can handle it.

Originally Posted by Peter firewood
I have to say, I’ve been pumping (on and off) for 15 years, with no gauge. My Current pump had a gauge which I removed to make it less cumbersome. If I can take more suction, and it feels ok, why not go for it. Seeing a number might do more harm than good, trying to attain that level, before your cock can handle it.

You know your cock’s limitations better than anyone.

I prefer to have a gauge when I pump, not that it matters, I always go for the extra yard and have to spend a week healing due to my foolishness.

BJ

My current pump was purchased at an auto parts store, as a hand held pistol-grip brake bleeder. $25.00 on sale.
It is brass, the best quality I’ve had so far. It came with a gauge, and I have seen this exact pump in pictures, sold as a penis pump. So guys, consider the auto parts stores as an alternate source for a good pump. I have made a cylinder of plexi pipe, and pvc plumbing fittings for the base flange and top-cap/hose connection. I have removed the gauge, because I have a feel for how much pumping is good. Also, I want to keep the rig simple for fast cleaning and storage. I have been pumping occasionally for years, and have gone from 6 & 1/2” to 7 & 3/4”. I now want to go for 8” plus, so my pumping has increased.
I am curious if anyone else has had luck with home built ‘units’. I will gladly post pictures of my device if it is possible on this site. Thanks for all the info, and curious if you have any ‘slick’ ideas for a cylinder.

PS; I’ve tried heat forming pvc central vac pipe to make a one piece cylinder, but this is difficult, by hand.

Your size in the pump is supposed to be slightly bigger than your size normally.right? I’m having a hard time even getting close to my normal size in the pump, and start feeling pressure (in a bad way, I think) if I up the suction. Could this have to do with too small of an entrance hole? I have a hard time getting everything in there - even though the tube itself is wide enough for me.


NBP Goal 14 | 14.5 | 15 | 15.5 | 16 | 16.5 | 17 | 17.5 | 18 | cm

MEG Goal | 12 | 12.5 | 13 | 13.5 | 14 | 14.5 | 15 | cm

Just an update, it was just a problem of not being erect enough when I enter the tube. All is well!


NBP Goal 14 | 14.5 | 15 | 15.5 | 16 | 16.5 | 17 | 17.5 | 18 | cm

MEG Goal | 12 | 12.5 | 13 | 13.5 | 14 | 14.5 | 15 | cm

Hi guys, quick question in terms of erect length inside the chamber when pumping with or without a gauge for that matter.

Following the guide, after my 5 minutes is up in the chamber should my penis have expanded past my normal state which gives me the temporary gains? Or can temporary expansion in length and girth still be achieved under erect length?

I have a bathmate. When I pump as the guide suggests I sit about 6.5/6.75” inside the chamber with not much temporary expansion after 5 minutes. Curious to know if I should pump to 6.5” and let the expansion take me past 7” which is my current length.

Thanks


Starting stats: 7" EL x 5" EG Current stats: 7.1" EL x 5.125" EG Goal : 7.5" x 5.75"

Top
1234

All times are GMT. The time now is 10:56 PM.