Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Trouble staying hard while pumping

Trouble staying hard while pumping

Hey guys just new to PE have tried Jelqing etc before and am about to start up again as I have more time on my hands ;) had a question about pumping I recently purchased a 10 inch penis pump I am currently around 8” BPEL and 6” Girth at mid shaft. The entrance to the pump has a rubber band which is quite tight and creates a circle mark at the base of my penis is this normal? Also I have noticed that the head of my penis rubs against the tube (the girth of the cylinder is easily large enough to fit me might be the angle in which I enter?) I just completed a 10 minuet pump and was fairly aroused got to around 8.5” inside the tube but as soon as I finished and pulled out which is also hard to get off (would I need lube?) I drop to a Semi straight away (Is that normal?) thanks for your help in advance.

I plan on starting the PE newbie routine soon my goal is 9” BPEL by 6.5 Girth.

I think it’s a good idea to use lube or lotion. My penis also touches my tube (I have a slight upward curve), and it definitely feels a lot worse without lube/lotion. It’s normal to come out of the tube not at 100% (I.e. Semi), no worries.
What pressure are you pumping at? Longer sessions at lower pressures (3-5 in Hg) seems to be the general consensus around here, I believe. Please, just make sure you be careful and take a it slowly; I know it’s mesmerising to see it grow in the tube ;)
If you haven’t already, I recommend you take a look at Vacuum Pumping 101

Good luck!

Thanks a lot for the info :) unfortunately this tube doesn’t have a gauge so I’m not sure how high I’m pumping at. I did crank it a little at the end of the session.


Starting size: (May 13 2007) 8.00" BPEL x 5.925" EG

Goal: 9.00" BPEL x 6.5" EG

Originally Posted by fedstheman
Hey guys just new to PE have tried Jelqing etc before and am about to start up again as I have more time on my hands ;) had a question about pumping I recently purchased a 10 inch penis pump I am currently around 8” BPEL and 6” Girth at mid shaft. The entrance to the pump has a rubber band which is quite tight and creates a circle mark at the base of my penis is this normal? Also I have noticed that the head of my penis rubs against the tube (the girth of the cylinder is easily large enough to fit me might be the angle in which I enter?) I just completed a 10 minuet pump and was fairly aroused got to around 8.5” inside the tube but as soon as I finished and pulled out which is also hard to get off (would I need lube?) I drop to a Semi straight away (Is that normal?) thanks for your help in advance.

I plan on starting the PE newbie routine soon my goal is 9” BPEL by 6.5 Girth.

Fedstheman -

The same happens to me, I go in hard and it stays expanded throughout the session but once the vacuum is released and I pull out my unit is flaccid but plump. I coat the tube with Baby Oil and it works well to eliminate any type of blisters and greatly reduces sticking when coming out of the tube. I bought a small plastic bottle (with a fine-spray pump) from the drug-store and use it to apply the oil into the tube and on my unit to keep my hands free of oil. It helps keep the exterior of the tube and hand-pump clean.

MMS

Same here, I assume that is standard. Usually I am not aroused, I have a very light pump and my session lasts 2hrs straight. My dick comes out pretty much moulded to the shape of the cylinder but in a flaccid state.

If you where pumping for EQ reasons, I suppose the procedure is different, including slipping a cock ring on straight after. However for PE I guess the point is to work out your CCs ;)


16.07.2011: Bpel 6.7" Eg 4.9" Fl 4.3"

08.05.2012: Bpel 7.2" Eg 5.1" Fl 5.8"

Just massage yourself to a full erection as soon as you come out of the tube and enjoy.


The primary goal of PE should be to make your penis as healthy as possible in both form and function. If you do that, increased size will follow.

Originally Posted by fedstheman

Thanks a lot for the info :) unfortunately this tube doesn’t have a gauge so I’m not sure how high I’m pumping at. I did crank it a little at the end of the session.

As soon as you can afford to, get a suet up with a gauge. You need a gauge to be consistant with you routine, but even more important, it’s very, very, easy to hurt yourself using too much pressure.

Top
Similar Threads 
ThreadStarterForumRepliesLast Post
Are Pumping Gains Permanent? Wrong QuestionLongVehiclePenis Pumps4404-03-2010 03:52 PM
Staying hard in tube/ball stretchingcommanderblopPenis Pumps309-04-2006 01:58 AM
Staying hard while Jelqingrs182Penis Enlargement Basics708-25-2005 12:08 AM
staying hardchas123Penis Enlargement Basics309-26-2003 07:56 PM

All times are GMT. The time now is 05:18 PM.