Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Cheap good pumper in Sweden or delivery to Sweden

12

Cheap good pumper in Sweden or delivery to Sweden

I’m a complete newbie to pumping and don’t know which pumper I should buy. I live in Sweden. I guess the pumper should be able
To measure pressure.

I’m 6,25 x 4,5 which size should I buy?

“One credit-card receipt for Swedish-made Penis Enlarger, signed by Austin Powers.”

Sorry, that wasn’t helpful.


"Sometimes a scream is better than a thesis." -Ralph Waldo Emerson

Originally Posted by garga22
I’m a complete newbie to pumping and don’t know which pumper I should buy. I live in Sweden. I guess the pumper should be able
To measure pressure.

I’m 6,25 x 4,5 which size should I buy?


Hey garga.

It might be worth doing a google search on your computer to see if there are any pump suppliers in Sweden. That way you could acsess possiblly several suppliers and find the best deal

For your girth you should get at least a 1 3/4” size tube as you would find a 1.5” too tight. For that extra size and being something 0f 5.5”£ it might be worth getting a flange to fit on the tube to give you a good seal, otherwise you might find your balls being dragged in (You can tie some ribbon around your balls and that will help keep them out but it can make things a bit sore)

There is a chance Mgus may be able to recommend stores in Sweden, so he may see your post and drop you a post to help out

Come back if you have any problems and we’ll have another go!

Good luck.

Petit


Don't be a lurker left out in the cold. :lurk: Join the happy band of donors!

Psst! The link is at the bottom of the page :bigwink:

Thanks for the replies. Didn’t find any solid supplier in sweden.(meaning that they are just selling various unknown pumpers).

Since I’m a newbie I think a will go for a known product like Dr Joel Kaplan’s (whats the big thing about him anyways?) which I know other ppl are using.

Thnks for the info mark001. I was checking theirs’ sizing table http://www.lapdist.com/sizing.htm . Who the hell is ordering a 8” width cylinder? . And secondly should I start with a 10” or an 8” in length (what difference does is it make?)

Hey Garga,

Try doing a search on Pro-Xzek . I found 3 hits and there were some mixed feelings so it might be worth a check there to see if that would affect your decision.

Also it will be worth checking out postage, and if there is any customs duty to pay.

Hope that helps

I live in the UK so I can only give you advice and sources from there.

PS the 8” girth tube is probably for a breast pump - Hope so anyway :D


Don't be a lurker left out in the cold. :lurk: Join the happy band of donors!

Psst! The link is at the bottom of the page :bigwink:

Buying within the EU, you pay only the VAT (moms) in the selling country. I ordered some household stuff you can’t find in Sweden for maybe 600 SEK and wound up paying another 250 or so for the services our customs and postal service rendered me when the decided to add customs. So finding a distributor from within the EU is worth the search.

I don’t pump, so I can’t give any advice at all on suppliers.


regards, mgus

Taped onto the dashboard of a car at a junkyard, I once found the following: "Good judgement comes from experience. Experience comes from bad judgement." The car was crashed.

Primary goal: To have an EQ above average (i.e. streetsmart, compassionate about life and happy) Secondary goal: to make an anagram of my signature denoting how I feel about my gains

Originally Posted by petitfaun
Hey Garga,

Try doing a search on Pro-Xzek . I found 3 hits and there were some mixed feelings so it might be worth a check there to see if that would affect your decision….


petitfaun,

apparently seems a good stuff.

But which are the dimensions?

Originally Posted by mark001
petitfaun,

apparently seems a good stuff.

But which are the dimensions?


Hi mark,
Sorry if I was a bit complicated there, But “in inches”

1¾” (or 1.75”) multiplied by the factor 3.14 gives a diameter of (aprrox) 5.5”

(and just to complete the picture)

!½” (1.5”) multiplied by 3.14 gives a diameter of 4.71” Which would not allow any expansion in the tube. (for garga that is.)

Do come back if you have any difficulty and I’ll try my hand at metrics

But just to complete 1” (inch) = 2.54cm. 1cm = 0.3937 inches

Hope that helps.

Petit


Don't be a lurker left out in the cold. :lurk: Join the happy band of donors!

Psst! The link is at the bottom of the page :bigwink:

Originally Posted by petitfaun
Hi mark,
Sorry if I was a bit complicated there, But “in inches”

1¾” (or 1.75”) multiplied by the factor 3.14 gives a diameter of (aprrox) 5.5”


petitfaun,
thank you.

Fortunately I have confidence with the Anglo-Saxon measurement system.

What I meant were the real dimensions of the Pro-Xzek Supreme Pump.

The cylinder is 9”x 2.25.

Originally Posted by mark001
petitfaun,
thank you.

Fortunately I have confidence with the Anglo-Saxon measurement system.

What I meant were the real dimensions of the Pro-Xzek Supreme Pump.

The cylinder is 9”x 2.25.


Sorry Mark if I sound a bit dim here. But the real dimension you ask for - so far as I can make out is the circumfernce of 2.25 which would be 7.1 inches (9” is the penis length of the cylinder)

If I’ve still got it wrong, can you explain what you mean by ‘real dimension’ as we may have different interpretations of ‘real dimension’ :)

Petit


Don't be a lurker left out in the cold. :lurk: Join the happy band of donors!

Psst! The link is at the bottom of the page :bigwink:

Originally Posted by petitfaun
Sorry Mark if I sound a bit dim here. But the real dimension you ask for - so far as I can make out is the circumfernce of 2.25 which would be 7.1 inches (9” is the penis length of the cylinder)

If I’ve still got it wrong, can you explain what you mean by ‘real dimension’ as we may have different interpretations of ‘real dimension’ :)

Petit

petit,

in your first post you did not say how big the cylinder in the Pro-Xzek kit is.
I discovered it is 9”x2.25”.

I know that 2.25” is the diameter and so the circumference is, as you said, around 7.1”.

Currently I am using a 9”x2” Lapdist cylinder and I think that I will buy a 9”x2.25” from the same brand.

Top
12

All times are GMT. The time now is 08:56 PM.