Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Revolutionary Clamp Design

12

Here is the clamp I created about a year ago. It is molded out of the same stuff silicone sleeves are made of, and it is very comfortable with no need to wrap.

Attached Images
Clamp.jpg
(21.9 KB, 100 views)

(Start BPEL 6.75 EG 4.8) 2006

(Now BPEL 7.12-7.25 EG 5.12-5.25) 2010

Where do you get the silicone mold?


Time to measure girth soon... previously 4.5", been targeting girth for months!

I made the mold. All you have to do is put a tube in the middle of the clamp for the size of hole you want. I used clay to round the inside so it slides on better. Then you pour the silicone. For the silicone to hold I drilled holes in the clamp so it (silicone) would flow through to the other side to make it more stable and not move around when you put it on. Maybe I will take some pics if anyone is interested.


(Start BPEL 6.75 EG 4.8) 2006

(Now BPEL 7.12-7.25 EG 5.12-5.25) 2010

cableclamp.com - You can get a bag of assorted clamps, including 2 medium clamps for $19.95 plus shipping ($6+/-) I tried several Walmarts and probably spent as much on gas without success. I used the smaller ones to organize some of my wires.

I use a 1” wide neoprene cock ring over a cut silicone sheath inside the cock ring. Works fine for me.


Last edited by dtwarren1942 : 02-09-2010 at .

kiltya,

Nice idea for silicone!

Originally Posted by kiltya
Maybe I will take some pics if anyone is interested.

I would be interested in seeing this.

Did you try making and using silicone rings/cylinders that were not attached to the clamp? If so, how did your molded clamp compare?

-aws

I made some rings and cylinders but they were just another step added to clamping, and it was a pain to get deep into the base.

This way you can push the clamp all the way down against the pubic bone with no problems.


(Start BPEL 6.75 EG 4.8) 2006

(Now BPEL 7.12-7.25 EG 5.12-5.25) 2010

Originally Posted by kiltya
I made some rings and cylinders but they were just another step added to clamping, and it was a pain to get deep into the base.
This way you can push the clamp all the way down against the pubic bone with no problems.

I am only “practicing” clamping at the moment as I am still working on length. However, whenever I have done a clamping set I have had the same problem as you describe.

I got another ecoflex silicone kit a few weeks back to make some new vacuum hanger sleeves. I still have a bit left. I might have to get out the drill and a few clamps and have some fun :)

Thanks! aws

I’m not sure if anyone else is clamping using the foam as a wrap, but now I’m clamping after pumping so I can’t use the first technique I described, because my girth is too big, here is my new technique….

Put the foam in the cable clamp and open the cable clamp, lube the base of your shaft and the foam, put the clamp (with the foam inside) around the base of your penis, and do whatever you can to get that first click in on the cable clamp.

Once you have the first click odds are there will be a gap between the 2 ends of the foam, fix this. It’s hard to describe exactly how to fix it, but its easy, you just kind of slide the foam so its together, pushing any skin you have out of the way, it sounds harder / riskier than it really is. Once the 2 foam ends are pushing against each other you can clamp it as tight as you want.


2010.02: 7-1/8" Bpel | 5-1/8" Mseg | 5-1/2" Beg

2010.06: 7-1/8" Bpel | 5-1/8" Mseg | 5-3/4" Beg

Top
12

All times are GMT. The time now is 02:34 AM.