New Hanging Device

Update:

I quit using the metal rings due to pain and issues urinating and thought it was causing those issues(in fact they were related to a tight pelvic floor due to my heavy lifting in the gym).

Came back to the drawing board over the past 2 weeks after seeing the diy silicone sleeve thread. Using my laser engraver, I cut whiteboard rings to fill a pvc tube and create this contraption. I tried just silicone but it only weighed about 4oz and thru hanging with the rings I found 8-12oz seemed to be the sweet spot for fatigue when worn all day.

Testing it today. Getting in was not bad using a noose hanger and a little water. I was able to pull thru and then lock it in with another diy silicone band with a smaller ID(1") OD on the smaller band is 1.5" matching the inside of the sleeve with the rings.

I may have to remove 2 rings and start slower with the weight. Already feeling fatigue after 3 hours in this thing.

It does require baggy clothing and standing to be effective. I happen to have a perfect job for this wearing baggy coveralls over my clothes and get about 14-20k steps per day.

Very happy with the fit and feel thus far. I may cut molds for a new silicone lock ring for behind the glans with a smaller ID that steps up. I think this would inspire more confidence that the contraption won’t slide off(I have a 1.1" flaccid diameter, the lock ring is 1" diameter. 3/4 or 7/8" may feel more secure). I don’t seem to be having any bloodflow issues, no cold glans, if anything I feel nice and toasty and loose.

I’m thinking some heavy blitz hanging sessions after I get home may be a way to maximize gains. 30-60sec at the highest weight I can handle, 2-3m light jelq to keep blood flowing, then another hanging set for 2-3m at about 60% of the heavy weight, followed by light jelqing again. Then wear the other sleeve I made(sans rings, with the lock ring to keep everything extended).

After one day of half day hanging, I have some upgrades to make. I also need to lower the weight, jumping back in at 12oz was too much. I’ll start with 2 or 3 rings(about 7-8oz) and progressively overload after I make the new sleeve. The lock ring probably isn’t needed. The main sleeve could probably be split on one side to make putting it on easier(the metal rings will keep it closed and tight. The internal tube needs grooves like the outside, 1.5" deep grooves and gripper walls that step down 1/8" every other 1/8"(so 1-3/8, 1-1/4, 1-1/8, 1, 7/8") 7/8" being just behind the glans. This should prevent slippage and keep the unit gripping the tunica better(maybe 2 of the gripper walls in a row, then step down 1/8", need to play with the design). I’ll have to cut new rings and pour a new sleeve to test.

The prototyping stage is so fun😎

What are you using to make the cutouts. Cnc machine?

There was a guy that posted awhile back how he gained an 1 1/2 in like 2 months from strictly wearing a one pound weight the first month then two the second month. He wore literally all day.

Laser engraver Aeon Mira 9.

I’d be damn near 9" in 2 months, that would be incredible😂

I cut the prototype into 2 pieces, split the smaller one to test as a ball stretcher. Works pretty well. Also works well on it’s own, the lighter weight doesn’t slip as much.

Due to the way I had the hanger positioned with the locking silicone ring, I ended up with a donut edema. My flaccid hang has been full and inpressive for 2 days post hang as well.

I plan to cut the rings for the new design this weekend and test it on Monday.

Made a new sleeve with some upgrades. Expanded the ring capacity to 7. Sleeve weight is 5.5oz with no rings, rings weigh 1.25oz each, which brings the grand total capacity to 14.25oz. The sleeve is 3.25" long and 2.125" in diameter(rings make it 2.5" diameter). Inner diameter varies. I implemented a stepped gripper system to grab the shaft and hopefully prevent slippage, also added a scallop to the interior. There are .5" long 1.5" deep chambers, followed by a narrowing down to 1.25" for .125" and then 1.125" for .125", then back to 1.5" for .5". Just behind the glans it steps from .875" up to 1.125" going up .125" every .125".

I haven’t field tested yet as I’m still dealing with a donut from the last prototype and it’s poor locking system. I already have an idea for an improvement on this design and am ordering more silicone to test it.

Let me know what you think.

That certainly looks slip-resistant!

I tried same rings over a silicone sleeves last year. Used the exact same ones. I think i used 5 and the pull was perfect. But a way to keep it all from slipping not so much.

Id buy one from you.

Once I get all the kinks worked out and make sure this thing is 100% I’ll reach out.

I’m actually considering starting a regular silicone sleeve business. Seems like no one can keep these things in stock and I have the ability to make some improved designs. I have my work cut out for me. Testing out some new silicones to see if I can get better elasticity.

I tried the last iteration on today. Getting in required the help of a noose hanger and lubing the grippers lightly. Wore it for about 5 minutes with 6 rings, very comfortable and felt super secure(I feel very confident it won’t slip off).

Now for the bad, the body is too thick. I need to play around with the mold and get the thickness down to somewhere between 1/8" and 3/16" max. 1/4" thickness doesn’t allow enough stretch to get in easily. I’ll be redesigning the whole unit to give it more of an ability to stretch, without losing it’s ability to grab the shaft at multiple points. I also think I can do away with the 1/4" thick reinforcement walls in front and back. They can be 1/8" and hold the rings just fine, and that allows room for an additional ring slot, bringing the total capacity to 8 rings and closer to a full pound hanging capacity. Shortening the ribs made sliding them onto the device much easier after it was on. So far so good. I’ll be cutting the next mold from acrylic. If I use a mixture of 1/8" and 1/16" acrylic I may be able to increase the ring capacity to 10, which would bring the capability of 1lb+ hanging.

I also ordered a few different silicones to test out as well.

I will also be designing regular sleeves for multiple uses, including sleeves with the scalloped interior. It seems there is a shortage of quality sleeves on the market and I’d like to bring my own offerings to the table.

Is this for ads?

Any chance you know were this post is?

I don’t know what post that is, but I managed to make an all day with no circulation issues with a penis sheath which I filled halfway with metal bars from old extenders, around 350 grams. I’ve been using for a week now. After heavy hanging sessions. So far I’ve gained around 0,8 centimeter in erect length. And it’s not newbies for I was already hanging and pumping. Don’t think it’s permanent though. But I can visually see the difference from 1 week ago. I’m stacking around 8 hours with the sheath with no circulation issues (I do 2 hours and then heavy hanging for 20 min, then sheath again). And I slide in a pumping session after last heavy hang of the day, then sheath again.

And now I became a scavenger for heavy metal chips to stick into the sheath to up my game 🤣