Who Can Pack a 2.25" Tube?

I have recently begun to 100% pack my 2” tube in less that 30 to 40 minutes. Packing the base is not a problem, but packing the 2” tube all the way to the head has taken me a while. My penis is more of a tree trunk shape and when I first started PE I had a good base measurement, but I started at at 4.5” at the circumcision scar. I am usually over 5 3/8” now in the same spot, but when I pump I can pack it at 6 1/4” with a 2” tube.

I would like to buy the new LAP oval tube and pack the 2.25” tube. I know I can pack the base, but it will take most likely a year or more to be able to pack the entire 2.25” tube.

I was wondering who here can pack a 2.25” tube? When I come out of a 2” tube fully packed, my dick is huge (to me). I cannot image having 3/4 inch more in girth.

So you’re getting about an inch of expansion? That’s pretty incredible. How long do you leave the pump on for? How’s the lymph buildup?

I can get about a quarter inch when doing sane pumping(less than 15 minutes at a time, less than 5hg) but haven’t seen much more than that.

I’m sure a few people here could pack a 2.25” tube, although at that point, your girth would be in the ridiculous 7” range.

I am a tree-trunk shape too and I have noticed some even-ing out of the girth after a year of PE. It would be so nice to figure out a way to target the top part of my penis — from right below the circ scar to the tip.

Congrats on packing the 2.0”!

I’ve been able to pack a cylinder that size. I don’t like the excess lymph though.

T.

I also have the tree trunk shape, but I’ve never had my glans pack my 2 inch cylinder. The rest of me packs it pretty good. Do you have any tips for packing it with the glans or just repetition? What pressures are you using?

Oh I just saw that part about the oval tube. I am really wanting one of those too and just wrote them about sizing. On the site it says:

"Our wide body cylinder helps to develop width and length up to 40% faster than a regular cylinder."

There is some discussion of this cylinder on the newart forum — people are saying they do pack it faster than they do a normal cylinder.

So maybe it would not take you that long.

Interestingly vacutech has a thickwall oval cylinder now too — the interesting part is that they talk about TWO measurements of the oval — width and height

Sizing chart here:

http://www.vacu tech.com/prodde … od=EllipticalTW

I do get some lymph buildup, but it is usually for instance not enough for my wife to notice. I agree 7” is ridiculous, that is why I want to do it.

I started with about 6” at the base, maybe 5.75”, but the increase at the top is what really made it look bigger. I think the larger oval will help me increase my base with out distorting the top.

Thanks

Technically the glans does not pack it the same as the shaft but as close as I am going to get. I use 5hg to 8hg and usually 40 minutes but sometimes 1 hour.

I use time, pressure 5hg to 8hg, heating pad and water. Then I try to keep the increased size for a few hours afterwards with a stayer.

I do not know how it would go faster? I know the increased size and width could allow more length in the tube. I think when I get a full erection in a round tube that I am thicker at the based than the tube is in diameter, it makes the tube push upward.

Kind of a pointless topic.
I started pumping with a 2.25” tube while my girth was only around 4.75”. I packed it right away, but it took an hour or more.
It was all fluid. Just a fat, puffy, donut.

Have you seen the freaks at tigerpump.com? They can pack a small keg if they try hard enough.

If you can pack that size tube with little to no fluid buildup then that is something.
I stick to my 1.75” . I pack it immediately, and get good length stretch without the excess fluid.

I saw some of those guys on Newart.com too. That is jsut sick. You could go from 4.75” to 7” in one hour? That is hard to believe even with fluid build up.