Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

What cylinder size can you pack / you use regularly?

View Poll Results:

What’s the largest cylinder size you can pack?

1.75"

1734.00%

2.00"

1836.00%

2.25"

918.00%

2.50"

510.00%

2.75"

00%

Other

12.00%
Total Votes: 50. You may not vote on this poll

What cylinder size can you pack / you use regularly?

Hello there I was curious about the average user’s default cylider size. I use a 2.25” which I pack quite quickly and a 2.50” which I am expecting to pack soon. I also use the 2.50” for huevos pumping.

How about you?

PS: I am not interested in knowing the size of cylinders used for both penis and scrotum pumping at the same time, only for penis pumping.


Last edited by mentula : 04-22-2010 at .

Whats your erect girth outside the pump? Must be pretty large to pack a 2.25 cylinder


15/03/10 - Starting size (6.0" length x 5.0" girth) Progress Report

03/09/15 - Current size (6.5" length x 5.5" girth)

??/??/?? - Goal size (8.0" length x 6.0" girth) Syler wants a bigger dick to hurt you with!

Guess I can’t really vote because I regularly use a 2.25” cylinder and it’s the only one I have. I only pack the bottom of it, but not nearly the towards the end of my penis. I got the slightly larger size to promote girth expansion and to prevent blistering. Although I have considered getting a 2” tube to lessen testicle pressure when going into the tube softer. (5.8”girth)


Start of Pumping and Routine:1/10/2010 BPEL 7.25", MEG 5.75", BEG 5.75"

Current:3/3/2010 BPEL 7.9", MEG 5.75", BEG 5.55" (got length and lost base girth?)

I started with a 1.5 which I now pack immediately. I also have a 1.5 elliptical which I pack about half way up. I am seriously considering moving up to 1.75.

I use a 1.75 tube that I pack about 80% of, but because of my upwards curve I doubt I will ever fully pack it which is fine with me I am gaining length that I couldn’t gain with hanging. 5.25” girth.

Originally Posted by Syler
Whats your erect girth outside the pump? Must be pretty large to pack a 2.25 cylinder

I have a baseball bat shape and one of the reasons why I started pumping was to correct that, also because the jelqing was making it way worse. The other reason for pumping was ED.

I think the only way to correct excessive base thinness is through pumping.

So now I pack the 2.25” very quickly at the top, and toward the end of the session I also pack the base. I don’t have a measure tape but my upper shaft and head are quite large normally.

I am aiming at packing the 2.50” sooner or later. Right now I can almost pack at the top. The base still has to grow though before I can pack at the base.

Also, I have an upward curve to the left. Well, for that you need a cylinder that tapers toward the top. That cylinder shape will direct the salami in a more straight fashion. If your cylinder is cylindrical and you have a curve, the head will smash against the walls and that won’t be pretty.

My routine by the way is based on pumping, some stretches, limp jelqing, erect dry or wet jelqing, ball pumping, and an exercise known as testicle breathing. I am pretty happy with the whole system. When I do erect wet jelqing, I use a cock strap for maximum ballooning. Only side effect I have had is some discoloration from the constant pumping. But I don’t mind because I have ED from excessive partying and old age and pumping is helping that.

God bless,
Mentula

PS: If you pack a size, move on to the next, or you’ll get too much bruising in the long run.


Last edited by mentula : 04-23-2010 at .

I started with a 1.75 then moved to a 2.25. I can’t pack it length wise. Just in the last week, after a long session, I packed a 2.50 width wise. I now start a session with the 2.25 and end with a cold water 2.50 .

Originally Posted by hsarge
I started with a 1.75 then moved to a 2.25. I can’t pack it length wise. Just in the last week, after a long session, I packed a 2.50 width wise. I now start a session with the 2.25 and end with a cold water 2.50 .

You are saying you pack a 2.5 cylinder? Holy shit, what is your girth?

I only pack the 2.5 after a long session that begins with hot water in the 2.25, then dry pumping with andractim, and finally cold water pumping with the 2 .5 . This takes a about 2 hours. I do quick pumping to 10 drop quickly to 5 and then gradually drop to zero; then start again. Repeat over and over. In the tube length is 8” and girth is about 8”. But drops quickly to 7” out of the tube. My normal bpel is 7.5 and girth is 5.75 normally. After pumping, girth can be 7” but only overnight. Oh, and the wife wants nothing to do with 7” girth. I’m just trying to get to 6” normal. I have never packed any 9” cylinder length wise. I also start pumping flaccid and not erect. I get a better length stretch in a 2.25 tube. When I am done pumping, I place a silicone tube on. I used the thread on ‘Making Silicone Tubes’ to make tubes of different sizes. This keeps things stretched and supported.

What’s up with your wife? She should welcome whatever the husband has to offer.

God bless,
Mentula

You can tell your not married.

I have 3 tubes: 1.75”, 2”, 2.25”. I can pack them all given enough time.

But what is the point to packing a tube that is way larger than your normal girth? It’s all just fluid.

I only use the 1.75.

Originally Posted by hsarge

You can tell your not married.

:)


For Lampwick, becoming hung like a donkey was the result of a total commitment.

Top
Similar Threads 
ThreadStarterForumRepliesLast Post
Size of cylindermescalinoPenis Pumps1110-05-2012 11:26 PM
Finding a different size homemade cylinder?Josh 14-11Penis Pumps1006-18-2008 12:27 AM
Help with cylinder size.G_want7Penis Pumps3004-03-2007 01:29 AM
Cylinder size selection questiona529612Penis Pumps208-22-2003 04:27 PM

All times are GMT. The time now is 05:26 AM.