Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

So. Tubes...

So. Tubes...

I have a 2.25” tube that works AWESOME for girth, not amazing, but AWESOME. (I need a 2.5 for staging..)

But it’s only 7.5 or so long, Which is my length erect. I hit the end during my sets, obviously.

I’m short on money. Cheap suggestions? Otherwise I’ll have to head back to the local sex shop for the XXL tube and pump haha.

Originally Posted by MNstrength
I have a 2.25” tube that works AWESOME for girth, not amazing, but AWESOME. (I need a 2.5 for staging..)

But it’s only 7.5 or so long, Which is my length erect. I hit the end during my sets, obviously.

I’m short on money. Cheap suggestions? Otherwise I’ll have to head back to the local sex shop for the XXL tube and pump haha.


About the only thing you can try is to buy a flange to fit on the bottom of the tube. Best have a look at some tube manufacturers sites, and see what they have on offer.

Hope that’s useful,

Petit


Don't be a lurker left out in the cold. :lurk: Join the happy band of donors!

Psst! The link is at the bottom of the page :bigwink:

I have a cylinder from each of these places and like both of them. Good construction, excellent seal:

————————————————————————————————————————
PictureBrite http://www.picturebrite.com/

P125 - Jim Diamond 2 1/4 inch cylinder w/free metal pump $27.95

Description does not say but it is 9” long. They may sell it with out the pump, I didn’t look too hard. (I got mine from them on ebay, which was slightly cheaper.)

————————————————————————————————————————————————————————
Boston Pump http://www.bostonpump.com/index.asp…WPROD&ProdID=12

STANDARD DESIGNED CYLINDER 9” length - $55.50

With the Boston one, if you want it longer, it is $5.00 extra per inch.

—————————————————————

Both cylinders work great. Note that the Boston Cylinder has what they call a “built in cockring” — basically that means that the entrance is a little narrower and thicker. That makes getting a seal a real snap.

In my experience, Boston Pump was slow to respond to emails and slow to ship. However I did receive my gear and it is excellent.

With picturebrite, shipping was fast, but there was a mixup in my order (wrong cylinder). When I contacted them they immediately shipped out a replacement, which I had in a day.

So in my experience both companies were great and the products are great.

Hope this helps.

Thanks a lot! Responses on thunder are always quick and helpful.

Yeah I’m not sure how long of a cylinder I’d need. I think I’ll use my current pump/cylinder for a month or two just as a little “added extra on for some of my PE days. I will then look into either a new cylinder, or a new cylinder/pump/gauge.

Does anybody have a good brand with a gauge that won’t cost me half my paycheck?

Since you already have the tubing and male connector, this really cannot be beat — around $25.00:

http://www.harborfreight.com/cpi/ct…temnumber=92474

This same pump is sold by several of the penis pump companies for $60.00 +. Here’s the thunder’s thread about it:

Lap pump = harbor freight tools pump

—-
I have this pump, it is really wonderful.

Your best bet is to go to your local harbor freight store if you have one. They seem to be pretty much everywhere.

I mail ordered mine thru the website since shipping was cheaper than gas. However, the standard shipping took about 2 weeks.

They do note on the website that there are better shipping options — but you need to phone in the order to thier 800 number.

Assuming your tube is 2.25 inch outside diameter, your local hardware should have rubber connectors for plastic drain pipes (rubber “pipe” about 3.5 inches long by 2.25 inch inside diameter,with screw clamps on each end). Simply remove one of the connectors. The beauty of this is that you can adjust (by sliding) the connector on your tube to end of with the head room you desire in the tube. Just make sure you don’t screw clamp directly on your tube lip, otherwise you may crack your tube. The nice thing about this is that the rubber eventually deforms at the base,taking on a more natural groin shape than a circle.The price has to be below $5.00. I apply Eucerin to the end of the connector, dabbing from the outside, in order to get a good seal and afterwards a short jelq series. My sweetie remarks all the time how my dick has a soft texture. She knows I pump, but not the Eucerin secret. Any thick moisturizing cream should work as a sealant, and much better than a sex lubicant.

Top
Similar Threads 
ThreadStarterForumRepliesLast Post
Thickwall vs Flaired bottom tubes?ineed9Penis Pumps1601-23-2006 09:22 PM
Anyone ever try the Colt brand tubesbob_jones2Penis Pumps301-23-2006 02:23 PM
Acrylic Tubespennywise05Penis Pumps102-19-2005 11:54 AM
Multiple tubes in 1/8” Increments for Uniform Girth DevelopmentMushroomPenis Pumps504-22-2003 02:21 PM

All times are GMT. The time now is 12:49 AM.