Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Selecting Your Cylinder Size

Originally Posted by gprent
Here you go: https://thickwall.co.uk

Yes, go with the 2" tube.

thanks mate.


Then- 5.7 x 4.7 (bpel x mseg)

Now- 7.1 x 5.1 (beg 5.5) // Goal-> 8 x 5.5+

Extender Log 2017

Not quite sure where to post this question, but though this looked like the best spot.

I’ve just started pumping with the aim of increasing length. However, I’m not sure when the best time to take measurements is? Just after pumping? In the cylinder? Hours after? What are your thoughts?


Dcla

Starting: 8th Nov 2018: BPEL 5 1/4; MSEG 4 3/8; BPFL 3 5/8; MSFG 3 7/8

48 hours after the last session. Should be plenty of time for the body to deal with the swelling.


Start 6.8” x 4.7” (4.9" BEG)

Latest 8.2” x 5.1” (5.3" BEG)

My pictures

Originally Posted by Lenny
48 hours after the last session. Should be plenty of time for the body to deal with the swelling.

Thanks, I’m going to leave it a few weeks before remeasuring I think.

I am 6.25 base girth but 5 at the tip and want to even out. Should I get a 2”? I use a Penomet and it’s made my base huge but not the head.


Started 5.5 x 4.2 Feb 2015

Current 7.25 x 5.5 - 6.25 Base girth?

Goal 7.75 x 5.75?

Originally Posted by Steinroid
I am 6.25 base girth but 5 at the tip and want to even out. Should I get a 2”? I use a Penomet and it’s made my base huge but not the head.

What is your girth right at your circ scar? I think it would be a safer investment to go with a 2.25” tube as a 2” tube would be a tight fit at the base. Your Penomet is probably around 2.5” at the base.


The primary goal of PE should be to make your penis as healthy as possible in both form and function. If you do that, increased size will follow.

5.25 at the scar. I’ve been wearing thick cockrings at the base in the Penomet because I want the top half of my cock to grow not the bottom anymore. I also clamp with 3-5 clamps to expand only the top half. But you guys with air pumps and small tubes seem to get insane expansion and pack the tubes with low pressure and my Penomet wants to rip my dick off. I’ve also stalled with this pump.


Started 5.5 x 4.2 Feb 2015

Current 7.25 x 5.5 - 6.25 Base girth?

Goal 7.75 x 5.75?


Last edited by Steinroid : 11-04-2017 at . Reason: Grammar

Originally Posted by Steinroid
5.25 at the scar. I’ve been wearing thick cockrings at the base in the Penomet because I want the top half of my cock to grow not the bottom anymore. I also clamp with 3-5 clamps to expand only the top half. But you guys with air pumps and small tubes seem to get insane expansion and pack the tubes with low pressure and my Penomet wants to rip my dick off. I’ve also stalled with this pump.

I don’t know how long you pump with your Penomet, but with air pumping it is good if you can work your way up to a 30 minute continuous pump set with a pressure of 5”hg and that should help with full shaft expansion as well as getting length expansion.


The primary goal of PE should be to make your penis as healthy as possible in both form and function. If you do that, increased size will follow.

Very Useful

Thank you for posting this as it is a nice reference to keep.

I do 20 to 30 mins and it seems MUCH more than 5 hg.


Started 5.5 x 4.2 Feb 2015

Current 7.25 x 5.5 - 6.25 Base girth?

Goal 7.75 x 5.75?

The Penomet is actually about 2.75 on the short side of the base. I just ordered a Leluv 2.25 to try out. Thanks for the advice. I’m tired of being stalled so I’m exploring all options that I can fit into my schedule. I’d hang but just don’t have that kind of time. Half hour a day is already a lot of time with kids and Work and overtime.


Started 5.5 x 4.2 Feb 2015

Current 7.25 x 5.5 - 6.25 Base girth?

Goal 7.75 x 5.75?

So I bought a LeLuv 1.5 cylinder and can’t get a proper seal and am having trouble locating a gasket/seal that will work fit it. Does anyone know where to find one that will fit it, as all the ones I can find are for the bigger cylinders.

Originally Posted by bubba9004
So I bought a LeLuv 1.5 cylinder and can’t get a proper seal and am having trouble locating a gasket/seal that will work fit it. Does anyone know where to find one that will fit it, as all the ones I can find are for the bigger cylinders.

Are you using any lube? Have you shaved your pubic hair where the cylinder fits?


Started 7.75x5.75

Currently: 9.75bpX6.75eg My Picture Thread

Goal:10.0bpX7.25mseg Building a thicker unit, click by click, pump by pump, jelq by jelq!

Originally Posted by Titleist
Are you using any lube? Have you shaved your pubic hair where the cylinder fits?

Yes, I’ve both shaved and used lube. I originally ordered their 1.75 kit off eBay, but determined I should be starting with the 1.5. With the 1.75, I do get a seal.

Originally Posted by bubba9004
Yes, I’ve both shaved and used lube. I originally ordered their 1.75 kit off eBay, but determined I should be starting with the 1.5. With the 1.75, I do get a seal.

What is your erect girth?


Started 7.75x5.75

Currently: 9.75bpX6.75eg My Picture Thread

Goal:10.0bpX7.25mseg Building a thicker unit, click by click, pump by pump, jelq by jelq!

Top

All times are GMT. The time now is 07:59 PM.