Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Selecting Your Cylinder Size

All right , the base of my left cc doesn’t fill up well, I don’t know why, but perhaps pumping could help. I’ll give it a try when they ship the pumps again, and when my wallet is filled with the easy-to -beat elders’ money. (<= humor)

Where to buy?

So I went to my local “sex shop” and acquired my first pump today. However the pump is much too large for me to use according to this sizing chart and my initial testing of the device, so where can I get a good cylinder with the pump and gauge for a good price?? I only ask about price since I’m out $60 from the one that doesn’t work as it should. Unless someone can suggest a way for me to be able to keep the seal good without my sack pulling into the tube and the pressure still not staying where it should.

Originally Posted by nitenite
So I went to my local “sex shop” and acquired my first pump today. However the pump is much too large for me to use according to this sizing chart and my initial testing of the device, so where can I get a good cylinder with the pump and gauge for a good price?? I only ask about price since I’m out $60 from the one that doesn’t work as it should. Unless someone can suggest a way for me to be able to keep the seal good without my sack pulling into the tube and the pressure still not staying where it should.

This is the best deal going for a Leluv system: http://www.ebay.com/itm/LeLuv-MAXI-…=item5410915d5b

Find your cylinder size using our size chart: Selecting Your Cylinder Size


The primary goal of PE should be to make your penis as healthy as possible in both form and function. If you do that, increased size will follow.

I want to go mainly for base girth.
On the page where I want to buy a conical shaped cylinder they tell me to get a diameter which is 1 -1,5 cm(0,4-0,6 in) bigger then my base diameter.
I have rather wide dick.
So while OP says according to my total girth I should get a 2.00 cylinder
.. it would mean that I would erect fit into it diamter wise jsut about with not much room to pump the base.
So I guess I go for at least 2.25 so I have some room to expand diameter wise.

I plan to purchase a pump sleeve for the base and ballstretcher/ring to avoid balls going inside.

Originally Posted by Walter5169

My largest part is 5cm, so close to the 5.3 cm (=2 inches) of the cylinder, does it mean I would expand more in depth rather than in width? Would it work on the cs?

Walter, did you buy one and what was your decision and outcome?
As I have ,like above written, almost the same problem.

I have just moved from a 2.00 to a 2.25 and found I should have done this ages ago

Hello, some feed-back will be helpful :) .

I have about 6.3” BEG, but about 5.6” MEG (almost 1” difference). I go for girth/length.

I have the option to select between 2.25” straight shaped pump versus 2.37” cone shaped pump. Is hard for me to decide.

Additional question: or is better to use a 2” pump? :)

Thanks in advance


Starting measures (1/1/2008): BPFL 4.50'', FG 4.50'', BPEL 6.25'', EG 5.25'' and so on .. :)

```````````````` 01/27/2009 : BPFL 5.70'', FG 5.10'', BPEL 6.90'', EG 5.60''

Originally Posted by Bicious
Hello, some feed-back will be helpful :) .
I have about 6.3” BEG, but about 5.6” MEG (almost 1” difference). I go for girth/length.
I have the option to select between 2.25” straight shaped pump versus 2.37” cone shaped pump. Is hard for me to decide.
Additional question: or is better to use a 2” pump? :)
Thanks in advance

You won’t even fit into a 2” cylinder. The 2.25” is the one for you.

Can you give me a link to the 2.37” cone shape cylinder? Not sure which one you are talking about.


The primary goal of PE should be to make your penis as healthy as possible in both form and function. If you do that, increased size will follow.

http://www.drugstore.com/california…-pump/qxp331476.

I see on this site it say 2.25”, but 6cm is 2.362”. Is not cone shaped like I thought :|.

So.. 2.5” versus 2.37” ? Matter of preference?


Starting measures (1/1/2008): BPFL 4.50'', FG 4.50'', BPEL 6.25'', EG 5.25'' and so on .. :)

```````````````` 01/27/2009 : BPFL 5.70'', FG 5.10'', BPEL 6.90'', EG 5.60''

In my humble opinion you want a cylinder better than this one, and a gauge.

Definitely do not buy the drugstore.com pump. It is low quality, no gauge and will not last long.

Where do you plan to buy the 2.25” cylinder pump?


The primary goal of PE should be to make your penis as healthy as possible in both form and function. If you do that, increased size will follow.


Starting measures (1/1/2008): BPFL 4.50'', FG 4.50'', BPEL 6.25'', EG 5.25'' and so on .. :)

```````````````` 01/27/2009 : BPFL 5.70'', FG 5.10'', BPEL 6.90'', EG 5.60''

That pump is also no good. The money you spend on that pump is going in the trash.

Even with the cost of postage, I think this is your best deal for a quality pump with a gauge that will last a very long time:

http://www.ebay.co.uk/itm/LeLuv-MAX…=item5410915d5b

There are also professional pumps available from Europe.


The primary goal of PE should be to make your penis as healthy as possible in both form and function. If you do that, increased size will follow.

Originally Posted by gprent
You won’t even fit into a 2” cylinder. The 2.25” is the one for you.

Can you give me a link to the 2.37” cone shape cylinder? Not sure which one you are talking about.

I disagree. It will fit. His base girth is likely extra skin and fat. The 5.6” midshaft will expand well in a two inch and he will get a greater length pull in the 2” tube than the 2.25” tube.

Interesting, I ask myself from a time. Possible with some squish it will fit. I think I will take 2 and 2.25, for steps process.

Thanks to both of you, inspirational, like always


Starting measures (1/1/2008): BPFL 4.50'', FG 4.50'', BPEL 6.25'', EG 5.25'' and so on .. :)

```````````````` 01/27/2009 : BPFL 5.70'', FG 5.10'', BPEL 6.90'', EG 5.60''


Last edited by Bicious : 01-29-2015 at .
Top

All times are GMT. The time now is 09:45 AM.