Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Pumping up huge

Originally Posted by dickerschwanz
Where is the edema happening? At the part where it is packing or like the head where it is exposed to the vacuum?

Edema is happening below the glans and swells up disproportionate to the rest of the shaft.. I may look into taping/ wrapping


21/09/2019. 6.2 inches bone pressed erect length.

Short-term goal 24/12/2019

7inches bone pressed erect length

Originally Posted by cheeba
Edema is happening below the glans and swells up disproportionate to the rest of the shaft.. I may look into taping/ wrapping

Absolutely stop air pumping. It’s a waste of time and dangerous. Take your pump into the bathroom, fill it with warm/hot water and get yourself in it. This will warm your unit up and there will be nearly no fluid buildup and zero chance of blisters. i’ve had too many bilsters and it sets things way off the timeline I was hoping to keep. It’s ok if water goes through your pump, it doesn’t matter, it does nothing to it. If you’re using a 1.75” tube and it takes a while to [pack it with lymph fluid bulid up I’d say you will have a much longer useful life with it if you start water pumpinig with it. And you won’t need to pump for so long to get the same effects, if not better and with less risk. Change out the water every 5-10 minutes as it cools since you want to stay as warmed up as possible. This should be the 100% official advice given for pumping and would save newbies and pros alike a lot of trouble.

Originally Posted by jung
Absolutely stop air pumping. It’s a waste of time and dangerous. Take your pump into the bathroom, fill it with warm/hot water and get yourself in it. This will warm your unit up and there will be nearly no fluid buildup and zero chance of blisters. i’ve had too many bilsters and it sets things way off the timeline I was hoping to keep. It’s ok if water goes through your pump, it doesn’t matter, it does nothing to it. If you’re using a 1.75” tube and it takes a while to [pack it with lymph fluid bulid up I’d say you will have a much longer useful life with it if you start water pumpinig with it. And you won’t need to pump for so long to get the same effects, if not better and with less risk. Change out the water every 5-10 minutes as it cools since you want to stay as warmed up as possible. This should be the 100% official advice given for pumping and would save newbies and pros alike a lot of trouble.

I couldn’t disagree more. My gains came from air pumping and being sensible. Watching my pressure and using constant heat.


Started 7.75x5.75

Currently: 9.75bpX6.75eg My Picture Thread

Goal:10.0bpX7.25mseg Building a thicker unit, click by click, pump by pump, jelq by jelq!

I’m with Titelist on this one as well. Also, depending on the kind of pump you have, getting water in it could ruin it.

I think Bathmate are mainly fun toys for guys to play with, get an air pump with a guage.

I’m glad you 2 guys disagree because I also air pump and would rather not deal with water as I’ve done it a few times and it’s a pain in the ass.

Also several pump manufacturers say that using water on the pump will dry out all the seals and eventually ruin it.


Forum rule #69. Your avatar must be of a woman's ass.

My adventures in PE:Damnit

Anything with seals and moving parts is going to wear out eventually. Not taking a side in this argument, just stating a fact. Also, different people and their units will react differently to different methods. So as far as “official advice” goes, remember, the official opinion on penis enlargement is that it is not possible, so take all “official advice” with a grain of salt.

Originally Posted by raybbaby
Anything with seals and moving parts is going to wear out eventually.

True.

Not to argue but putting the pump in water will wash away the grease on the moving parts and dry out the seals. That’s what the manufacturers stated.

Certainly agree with the rest of your post and if something works for someone. Great :)


Forum rule #69. Your avatar must be of a woman's ass.

My adventures in PE:Damnit

I have a mityvac that has been repeatedly exposed to water (plastic one from v-tech) for a long time now and works jus fine… I don’t use it much water hasn’t hurt the unit … it does need to be re lubed once in a while er go silicone sex lube pored into he hole the piston comes out of other than that still spot on.

I personally don’t agree with everyone must use my approach attitude, jus saying no worries if ya get a little water in your mityvac hand pump, it’ll be fine

Originally Posted by sweeternuts
It does need to be re lubed once in a while er go silicone sex lube pored into he hole the piston comes out of other than that still spot on.

I personally don’t agree with everyone must use my approach attitude.

And that is exactly what the manufacturers state. That if it is exposed to water it needs to be relubed/greased otherwise the seals will prematurely fail.

I’m just simply repeating what the manufacturers suggest and I’ve taken a pump apart and see why water getting in there would dry out the seals and also could possibly rust the spring.

Agree. There’s no 100% it has to be done this way when it comes to PE.


Forum rule #69. Your avatar must be of a woman's ass.

My adventures in PE:Damnit

I pump up to 10mg sometimes. No problems. But incremental increase is something ill try.

Definitely recommend pumping with a electric blanket wrapped around the tube.. Helps with expansion so much


21/09/2019. 6.2 inches bone pressed erect length.

Short-term goal 24/12/2019

7inches bone pressed erect length

And minimises edema


21/09/2019. 6.2 inches bone pressed erect length.

Short-term goal 24/12/2019

7inches bone pressed erect length

Yes, I got a 9”x9” heating pad at Walmart, almost a perfect size towrap the tube,, works great for expansion and edema, makes a big difference. Only has off and on though, so you have to cycle it a bit during long sessions.

Are you guys holding the heating pad in place the entire time or using something else?

I’ve been trying to think of something that will hold it fairly snug yet be easy to get on and off.


Forum rule #69. Your avatar must be of a woman's ass.

My adventures in PE:Damnit

Top

All times are GMT. The time now is 11:31 AM.