Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Pump Problems

Pump Problems

I have a newer pump from Harbor Freight. Today it will not go any higher than 5HG. Don’t really need more, but I took the hose off the pump end and put a finger over the reduction nipple and still nothing over 5HG. Anyone else had this to happen and if so, were you successful on a repair or remedy?

Thanks

Never heard of that problem before. Maybe try the pump up to 5 with your finger over the nipple and give the gauge a little tap to shake the needle free. It might just be stuck on something minor and need a little jolt to set it free.

Or, continue to use it as is, but always pump just below 5, just to make sure you are not inadvertently pumping at some unknown pressure over 5.


The primary goal of PE should be to make your penis as healthy as possible in both form and function. If you do that, increased size will follow.

Mine just arrived this afternoon, from Harbor Freight. It seems ok. You might check & look to see that the last fitting on the pump cylinder is screwed in tightly. This is the fitting you attach the hose to, and that the gauge is also screwed in tightly. Did your pump used to go above 5hg ? If you have dropped it, you may have caused something to be leaking air.

Fortunately, it is not too expensive to replace.

Pump problem

Hey this is off topic but what do you think I should do if I cracked my pump? I rinsed it through with really hot water, this is why it’s cracked. Do I need to order a new one?

Is the gauge screwed in tightly?

Originally Posted by Mammoth
Hey this is off topic but what do you think I should do if I cracked my pump? I rinsed it through with really hot water, this is why it’s cracked. Do I need to order a new one?


If it is cracked it probably won’t hold a vacuum. If it does then it might implode upon your penis .

Get a new one.


Don't be a lurker left out in the cold. :lurk: Join the happy band of donors!

Psst! The link is at the bottom of the page :bigwink:

Sometimes, again sometimes crazy glue will seep into the crack and seal it. If that don’t work then a new tube will need to be bought.

I would get a new tube.

Originally Posted by petitfaun
If it is cracked it probably won’t hold a vacuum. If it does then it might implode upon your penis .

Get a new one.

Ouch!

I agree. Buying a new cylinder is a lot cheaper than buying a new penis :)

Originally Posted by Tennsteven
I have a newer pump from Harbor Freight. Today it will not go any higher than 5HG. Don’t really need more, but I took the hose off the pump end and put a finger over the reduction nipple and still nothing over 5HG. Anyone else had this to happen and if so, were you successful on a repair or remedy?
Thanks

Are we still talking about the same problem? It originally sounded like the pump does not create a vacuum even when the tube is not attached. I.e., a cracked tube would not be causing the problem.

Good thought plustwo. I would get a new kit.

Thanks guys, I’m not a regular member here so forgive me for not replying quickly. I have a larger pump from LA pump, 10 inches long and 2 1/2” (I think) in width opening. Of course it makes my penis huge, but I think it’s wiser to use a pump that fits well and allows for more gradual expansion. Also, I don’t have the time and privacy to pump every day. Could I possibly warm up, jelq, and pump on a slightly higher pressure and still gain some girth?

Top
Similar Threads 
ThreadStarterForumRepliesLast Post
Where to buy pussy pump? And is LA Pump still around?venicejayPenis Pumps1207-18-2011 09:39 PM
Dr. Kaplan's hand pumpjallenPenis Pumps807-13-2008 09:41 AM
First Pump session reflectionsviva_la_revPenis Pumps1703-07-2006 08:11 PM
Why not just pump and stretchskitola11Penis Enlargement Basics105-21-2005 06:51 PM
Had my first pump sessionhyyprrPenis Pumps210-10-2004 10:49 PM

All times are GMT. The time now is 11:29 AM.