Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Packing

Packing

Guys I’ve noticed I’ve been packing my tube a lot faster at the bottom but it feels like my unit gets stuck and is unable to be pulled. I milk the tube and also use evo oil and coconut oil to ensure its slippery. Will these gains translate into solid gains. It doesn’t seem any bigger outside the tube after 6-8 hours,but I notice it’s getting huge inside. Also I usually only do 3hg now. 4-5 for a few minutes sometimes. I am using a 1.75 but my 2 inch feels too big. They are both Boston cyclinders, the 1.75 is a different and I love how snug it is. The 2 inch one is a lot bigger and sucks my scrotum in. I don’t really know what to do.

Continue with the smaller cylinder. Are you using constant heat (wrapping the cylinder with a heating pad)? You said your packing the bottom of the cylinder. What about around the mid shaft area?


Started 7.75x5.75

Currently: 9.75bpX6.75eg My Picture Thread

Goal:10.0bpX7.25mseg Building a thicker unit, click by click, pump by pump, jelq by jelq!

Continue with the smaller tube. Otherwise you run the risk of fitting an oversize tube and forcing your base girth to expand much faster than your mid and upper shaft. This will give you radically different numbers in different parts of your penis and make it less uniform. Take it from someone who sized up in cylinders too fast at too high a pressure.


Now: 8.875" BPEL x 6.125" MSEG as of 8/12/2016 It's a long story but...

Then: 6.25" x 4.37" in 8/2009 Are you new to PE? Here's some advice I wish someone had given me when I first started.

My big secret? My methods. There is no "Holy Grail" of Penis Enlargement. Only time and effort works. I'm 7 years in and counting. Put the work in then the gains will come. All you have to do is keep the faith.

Yes I wrap the tube with a heating pad

Go into the cylinder erect and you shouldn’t have any issues. Going in soft and allowing the pump pressure to engorge your penis might cause it to get “stuck” even with oil.


Started: 01/01/2015 ~ BPEL: 7.2 inches. EG: 5.5 inches. [05/01/2015: BPEL: 7.6 X 5.5.] [08/06/2015: 7.75 X 5.5]

Goal: BPEL: 8.2 inches. Better EQ.

All hard work brings a profit, but mere talk leads only to poverty. ~ Proverbs 14:23

I use my 2” cylinder for twenty minutes and then switch to my 2.25” cylinder for a 10 minute session.


Start 11/09 BPEL: 5.5", EG: 4.4"

Current. BPEL: 6:4", EG: 5.5"

When you switch to your larger tube you will start out sucking in mostly fat around the base. I think that may be why pumpers can get the baseball bat effect. The fat retards growth at the bottom (like a smaller tube would ), but then the vacuum pulls harder above the fat.

I am not implying your fat. I am rather thin and I still pull in a little fat. It makes a good seal.

Ok I just had another session with my 1.75 and it’s starting to hurt. It digs into my pubic region and is just unpleasant. Why would this happen? Also not going over 4hg.. I looked at the cylinder difference, my 1.75 is the Boston contoured design, the 2 is the Boston standard. They feel like night and day difference.

Originally Posted by jl39

Ok I just had another session with my 1.75 and it’s starting to hurt. It digs into my pubic region and is just unpleasant. Why would this happen? Also not going over 4hg.. I looked at the cylinder difference, my 1.75 is the Boston contoured design, the 2 is the Boston standard. They feel like night and day difference.

Does the “standard” have a flanged base? That could account for the better comfort.


Start 11/09 BPEL: 5.5", EG: 4.4"

Current. BPEL: 6:4", EG: 5.5"

Top
Similar Threads 
ThreadStarterForumRepliesLast Post
Gains related to packing a cylinderLaehPenis Pumps508-07-2010 02:46 PM
Packing may contribute to girth gains.JambazPenis Pumps905-09-2007 09:08 PM
Tube Packing QuestionbrianrexPenis Pumps803-16-2005 01:03 AM
Packing at the head. Need new cylinder?StretchinPenis Pumps1011-12-2004 04:30 AM

All times are GMT. The time now is 03:01 AM.