Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

new inner tube trick to keep sac out of tube

new inner tube trick to keep sac out of tube

I’m sure some do this already but they are new to me anyway and I didn’t see anything about them. The first is to keep your sac out of the tube. What I do it take a 4 inch section of inner tube and cut down it so it is a flat square 4 inches X 2.25 inches then I use a quarter and place it in the middle and cut around it. I slide this down my cock like a cock ring but the extra lays flat and my tube seals to the rubber and keeps most of the sac out.

I just use a large rubber cockring for this purpose. I.e., one that is almost ‘loose’ when erect (i.e., larger than one would use for sex).

I’ve tried that also but I still got some sucked in. This way the tube seals to the inner tube that is a flat piece of rubber with a hole in it so the only thing that goes through is your penis. The inner tube should look like a square with a hole in the middle. I hope I’m describing it ok

Well Guys if you really want to keep those nuts outa the way do this: Take a “Good” length of soft cotton cord about 1/4” diameter about 40-50 inches long. Doubele it. Make a loop in the end of the middle part. Put the loop over your right wrist and grap your nuts and stretch them out slightly. Ease the loop over them and sinch them up slightly. Pass the two end of the cord under your scrotum and up you butt crack like a thong would be. Pull tight enough to put a bow know in the front and thus gentlly pulling them back. Proceed to pump up. Try it, work with it a bit and you’ll like it—what do you have to loose. Beware of too mall of a cord that could cut the circulation away. Again Beware and use a thick soft cord or make yourself a slingshot out soft leather. Steve.

Originally Posted by GonaBeBig

I’m sure some do this already but they are new to me anyway and I didn’t see anything about them. The first is to keep your sac out of the tube. What I do it take a 4 inch section of inner tube and cut down it so it is a flat square 4 inches X 2.25 inches then I use a quarter and place it in the middle and cut around it. I slide this down my cock like a cock ring but the extra lays flat and my tube seals to the rubber and keeps most of the sac out.

Is the inner tube actually connected to the pump? Do you have a picture of this setup and how it looks in the pump? Also, any particular size inner tube recommended?


Jan 1st/07 - 7 14/16'' BP 4 Month Growth Comparison Pics - First Clamping pics

Feb 2009 - 8.15'' BP / 7.4'' NBP x 5.1'' EG New pics

Sorry I don’t have any pictures. It is not conected to the tube at all. I cut a 4 inch section of inner tube. Then I cut it length wise so it is no longer a tube but is a flat square piece of rubber. Then I cut a hole in the middle of it. I slide my penis in to the hole o cut out and now there is a flat piece of rubber that is laying flat on me that the tube will suction to and not suction to my fat pad or sac area because the rubber is in the way. Does that help?

Originally Posted by GonaBeBig

Sorry I don’t have any pictures. It is not conected to the tube at all. I cut a 4 inch section of inner tube. Then I cut it length wise so it is no longer a tube but is a flat square piece of rubber. Then I cut a hole in the middle of it. I slide my penis in to the hole o cut out and now there is a flat piece of rubber that is laying flat on me that the tube will suction to and not suction to my fat pad or sac area because the rubber is in the way. Does that help?

Sounds easy enough. I’ll give it a try. Where did you get the inner tube? Sure they have them at Walmart or something like that.


Jan 1st/07 - 7 14/16'' BP 4 Month Growth Comparison Pics - First Clamping pics

Feb 2009 - 8.15'' BP / 7.4'' NBP x 5.1'' EG New pics

I got mine at walmart they only had one size so I got that

I’ve been very pleased with white Plasti-dip.

http://www.plastidip.com/consumer/index.html

I think it is better than black, seems to hold up better. You can get a can of the liquid (not spray) for about $7.00 usd at Home Depot or Harbor Freight. It will last forever!

What is great about this is you can dip as many coats as you need to narrow down the mouth of the tube, it not only makes for a much better, easier seal, it can also act as a cockring and increase the internal pressure of your penis when pumping, allowing better results with less vacuum.

If you no longer want it, or if you want to redo it, it is a simple matter to peel it off the tube.

I have used it on my gravel filter tube, and it has really made it a great cylinder. My only regret is that I didn’t try this 2 years ago!

With this, I really think you could buy an oversize tube and just dip it to make the entry perfect, then just remove it or redo it as you get bigger.

When you go to put on multiple layers, you only have to wait 20-30 minutes between them. When you go to use it, make sure you let it cure overnite to be sure.

Originally Posted by GonaBeBig
I got mine at walmart they only had one size so I got that


Another question for you man…

I was in Walmart tonight and was about to buy an inner tube but had a few more questions. I was thinking that since the cylinder isnt really creating suction with your skin but instead its the inner tube, then you have to be completely still otherwise the pump could fall off or move around since its not being sucked to you directly. When you use the inner tube with it, does it still allow enough suction to pump your cock up really good w/o sucking up to your skin and into your pubic bone? Just a few thoughts I had, hope it makes sense!


Jan 1st/07 - 7 14/16'' BP 4 Month Growth Comparison Pics - First Clamping pics

Feb 2009 - 8.15'' BP / 7.4'' NBP x 5.1'' EG New pics

Sorry I didn’t respond sooner. The pressure still holds it in place. I use mine after my regular work out. I pump to 5hg disconnect the pump from the tube and leave it on in the shower as I get around. When I’m almost done in the shower I slide my finger between the inner tube and my skin to release the pressure and then finish my shower.

Doesn’t your tube get wet/moisture in it while you are showering?

If moisture could get in the tube you would have an air leak and the tube would fall off. So no there should be no moisture getting in the tube.

Top
Similar Threads 
ThreadStarterForumRepliesLast Post
Looking to trade quipment. Have you out grown you Tube and need a bigger one?xefonPenis Pumps106-17-2005 01:03 PM
Twin Tube SessionskeptdickPenis Pumps310-01-2004 08:55 AM
New Tube?DavPenis Pumps505-08-2003 06:00 PM

All times are GMT. The time now is 04:49 AM.