Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Narrow cylinder at base

12

Narrow cylinder at base

Guys, where can I find a cylinder that is narrow at the base and widens towards the top ?

I’m asking this because I tried using a bigger cylinder and it tends to draw my balls inside.


Starting stats: 6.4" / 5.6" Current Stats: 7.4" / 5.8" Short term goal: 7" / 6" Long term goal: 8" / 6.5"

Just get a smaller tube.

smaller cylinder

I bought a Metalvacll pump with 2 inch cylinder, which I think however is slightly too wide for me.

I therefore want to buy a smaller cylinder, but I was wondering wether a tube from a different manufacturer will fit to the Metalvacll pressure gauge?

For those who would be interested,

the MetalvacII hose fits perfectly on a leluv cylinde

However i received the narrower cylinder today 1.75” and its too small! (the 23” i find a bit too big!)

who wants a 1.75”?

Originally Posted by sta-kool
Yes, go down a size. You will eventually grow into your current cylinder.

ska and pukers,

My penis is wider at middle and narrower at base/head -someting like this ()


Starting stats: 6.4" / 5.6" Current Stats: 7.4" / 5.8" Short term goal: 7" / 6" Long term goal: 8" / 6.5"

I am also looking for a tube that is narrower at the base and widens towards the top. Does anyone make these?

EJ, had any luck finding one ?


Starting stats: 6.4" / 5.6" Current Stats: 7.4" / 5.8" Short term goal: 7" / 6" Long term goal: 8" / 6.5"

Boston pump works makes some cylinders that are roughly 1/4” in diameter smaller at the base. They call it a “built in cockring”. I have a 1.75” and its 1.5” at the opening.

It helps with what you’re speaking of. I thought it would be detrimental to my pumping as I am well over 5.5” base girth(1.75x3.14=5.5). I can assure you it has no ill effect on it. In fact, since I began using it my base girth has been massive after a pump session.

Originally Posted by G263
Boston pump works makes some cylinders that are roughly 1/4” in diameter smaller at the base. They call it a “built in cockring”. I have a 1.75” and its 1.5” at the opening.

It helps with what you’re speaking of. I thought it would be detrimental to my pumping as I am well over 5.5” base girth(1.75x3.14=5.5). I can assure you it has no ill effect on it. In fact, since I began using it my base girth has been massive after a pump session.

My base girth is slightly more than 6” and I use a 1 1/2” tube mostly, as it really stretches me for length, but counterintuitively has made my girth larger to the point my wife has actually commented!

I have been doing PE for nearly five years Noe and it never ceases to surprise me.


Began December 2009 at 5 7/8" length and 5" girth.

As of December 5th 2012 7 3/8" BPEL and 6 1/8" base girth.

Going for the magic 8"x6"

Originally Posted by a-unit
My base girth is slightly more than 6” and I use a 1 1/2” tube mostly, as it really stretches me for length, but counterintuitively has made my girth larger to the point my wife has actually commented!

I have been doing PE for nearly five years Noe and it never ceases to surprise me.

That sounds about right haha. Every time I think something may not be the way to go it is exactly the opposite haha

Originally Posted by a-unit
My base girth is slightly more than 6” and I use a 1 1/2” tube mostly, as it really stretches me for length, but counterintuitively has made my girth larger to the point my wife has actually commented!

I have been doing PE for nearly five years Noe and it never ceases to surprise me.

Hows your midshaft girth? Greater than 1.5”? With the length stretching you feel it stretching your shaft?

Originally Posted by djrobins
Hows your midshaft girth? Greater than 1.5”? With the length stretching you feel it stretching your shaft?

Absolutely. My midshaft girth is just less than 6” around.

With the narrower tube I feel a tremendous direct pull on the entire shaft from the inside out that is extremely fatiguing.

Once erect in the narrow tube I can also kegel and pull on the base of the shaft by tugging the tube slightly while pumping which adds to the pull on the shaft.


Began December 2009 at 5 7/8" length and 5" girth.

As of December 5th 2012 7 3/8" BPEL and 6 1/8" base girth.

Going for the magic 8"x6"

Top
12
Similar Threads 
ThreadStarterForumRepliesLast Post
Too small cylinder limit expansionclienthesPenis Pumps308-11-2010 11:09 PM
Pumping Question re cylinder size and packingmugglesPenis Pumps1107-21-2008 11:33 PM
Confusion over 2nd cylinder size.ynottryPenis Pumps910-08-2007 08:34 PM
Photo-Documented DIY cylinder guide!secjayPenis Pumps1612-19-2004 04:22 PM

All times are GMT. The time now is 12:54 PM.