Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Home made pump.

Originally Posted by a-unit
And my wife is noticing the changes to my dick.

More sensitive, more easily aroused, and seems to be a little thicker as well.

Makes it worth the effort. Way back when, my wife just thought it was a for of jerking off. Now she’s a believer.


Started 7.75x5.75

Currently: 9.75bpX6.75eg My Picture Thread

Goal:10.0bpX7.25mseg Building a thicker unit, click by click, pump by pump, jelq by jelq!

Originally Posted by Titleist
Makes it worth the effort. Way back when, my wife just thought it was a for of jerking off. Now she’s a believer.

I hear you.

Mine has no idea.

Or she does and is good enough to no say anything.


Began December 2009 at 5 7/8" length and 5" girth.

As of December 5th 2012 7 3/8" BPEL and 6 1/8" base girth.

Going for the magic 8"x6"

So, I used a surgical glove with the fingers cut out as a seal for my pump and wow, did that make an improvement.

I’m going to try bicycle inner tube next.


Began December 2009 at 5 7/8" length and 5" girth.

As of December 5th 2012 7 3/8" BPEL and 6 1/8" base girth.

Going for the magic 8"x6"

Originally Posted by a-unit
I hear you.

Mine has no idea.

Or she does and is good enough to no say anything.

My girl is like that too. Great that your pumping is working for you.

Keep up the good work!


Starting size: 7.48" X 5.51" Currently: 10.1" X 6.4"

Heat is the key!

Originally Posted by monochrome
My girl is like that too. Great that your pumping is working for you.

Keep up the good work!

I will keep fine-tuning it.

I’m still waiting for my clear tube so that I can see what’s going on.

Thanks for the encouragement!


Began December 2009 at 5 7/8" length and 5" girth.

As of December 5th 2012 7 3/8" BPEL and 6 1/8" base girth.

Going for the magic 8"x6"

I’m still amazed at the change in my dicks physical appearance.

More veins, more flaccid. Awesome.

And it works better too!


Began December 2009 at 5 7/8" length and 5" girth.

As of December 5th 2012 7 3/8" BPEL and 6 1/8" base girth.

Going for the magic 8"x6"

Originally Posted by a-unit
I made my first home made pump today.

2” inside diameter ABS pipe with an orange test cap to seal it, with a connector and narrow gauge pipe to suck the air out with my mouth.

Verdict; I need a better seal at the connector because I have to suck air out every few seconds to maintain suction, but I was really surprised how much suction the device generates.

I used a small length of bicycle inner tube to seal the base today and it works really well.


Began December 2009 at 5 7/8" length and 5" girth.

As of December 5th 2012 7 3/8" BPEL and 6 1/8" base girth.

Going for the magic 8"x6"

Originally Posted by sparkyx
LOL, welcome to pumping!

I wish I’d tried this sooner, but here we are now.

Little sore this morning. My wife seems to notice the difference and wants more.


Began December 2009 at 5 7/8" length and 5" girth.

As of December 5th 2012 7 3/8" BPEL and 6 1/8" base girth.

Going for the magic 8"x6"

My polycarbonate tube arrived at the supplier today.

Six foot section for $27 and they wouldn’t cut me a 10” piece, so I will see whether I can justify the extra cost vs. Continuing with the opaque tube.

Still fine tuning the pumping method and since my wife has been asking for afters daily, my dick is so tired in the tube that I’m worried about over training.


Began December 2009 at 5 7/8" length and 5" girth.

As of December 5th 2012 7 3/8" BPEL and 6 1/8" base girth.

Going for the magic 8"x6"

Nice to hear it working well. One way I fixed air leak issues on my homemade system is: I use a schedule 80 2inch PVC pipe, weld on a reducer cap which takes it to a 1/2 inch NPT threaded interface, screw in a plastic NPT to hose fitting then simply shove the hose onto the end of the fitting. I either suck the air through the hose or hook the hose up to a hand pump with gauge. Also put an inline valve in the hose.

No leaks and very easy. So if you keep having leak issues you might try this approach.

Originally Posted by Laeh
Nice to hear it working well. One way I fixed air leak issues on my homemade system is: I use a schedule 80 2inch PVC pipe, weld on a reducer cap which takes it to a 1/2 inch NPT threaded interface, screw in a plastic NPT to hose fitting then simply shove the hose onto the end of the fitting. I either suck the air through the hose or hook the hose up to a hand pump with gauge. Also put an inline valve in the hose.
No leaks and very easy. So if you keep having leak issues you might try this approach.

Excellent idea!

I’m going to get the parts next time I’m at home Depot without the wife.


Began December 2009 at 5 7/8" length and 5" girth.

As of December 5th 2012 7 3/8" BPEL and 6 1/8" base girth.

Going for the magic 8"x6"

Originally Posted by a-unit
I made my first home made pump today.

2” inside diameter ABS pipe with an orange test cap to seal it, with a connector and narrow gauge pipe to suck the air out with my mouth.

Verdict; I need a better seal at the connector because I have to suck air out every few seconds to maintain suction, but I was really surprised how much suction the device generates.

Wow A Unit your pretty inventive. Maybe you can help come up with a new electric car someday that goes from 0 to 60 in 5 seconds


marshall

Originally Posted by marshall09
Wow A Unit your pretty inventive. Maybe you can help come up with a new electric car someday that goes from 0 to 60 in 5 seconds

That’s funny.

Does it have to be electric?


Began December 2009 at 5 7/8" length and 5" girth.

As of December 5th 2012 7 3/8" BPEL and 6 1/8" base girth.

Going for the magic 8"x6"

The inner tube rubber deteriorates quickly and tears over the edge of the tube.

I have tried sanding the edges smooth, but it doesn’t seem to help.


Began December 2009 at 5 7/8" length and 5" girth.

As of December 5th 2012 7 3/8" BPEL and 6 1/8" base girth.

Going for the magic 8"x6"

Top

All times are GMT. The time now is 02:21 PM.