Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

has anyone seen this one before?

12

has anyone seen this one before?

http://www.shopwiki.com/search/Colt…_Sleeve?loose=t

I was looking around on here and it shows that you can get a metal pump for about 50-60 bucks, and then buy the cylinder for about 20 bucks and there you go.

Does anyone think this is a reputable pump?

And also, would I need a silicone sleeve? Are they to protect your balls from getting sucked into it?

Check out the thread “lapdist equals harbor freight pump” or something like that. Search for the terms.


regards, mgus

Taped onto the dashboard of a car at a junkyard, I once found the following: "Good judgement comes from experience. Experience comes from bad judgement." The car was crashed.

Primary goal: To have an EQ above average (i.e. streetsmart, compassionate about life and happy) Secondary goal: to make an anagram of my signature denoting how I feel about my gains

Yes, I have looked into that, but I’m weighing my options of buying an actual penis pump or building my own. I have a harbor frieght close by. Basically I was asking if those pumps in the links were reputable.

Also, since I am new to the whole pumping aspect of the PE world, I’ve read that sometimes due to the dry pumping your head actually gets bigger then the rest of your shaft. Does this happen or is this due to over pumping. I ask this because I was researching water based pumps.

Probably the place with the lowest price and still getting good value is picturebrite. They have the same metal pump and low cost cylinders that are good quality. The problem with Harbor Freight is the pump doesn’t have the quick disconnect couplings and you have to buy them elsewhere.


The primary goal of PE should be to make your penis as healthy as possible in both form and function. If you do that, increased size will follow.

I see. Well, what would you say about the water pump compared to the air pump? Would you say the water pump is better? But I dont have a bathtub to use it in. Can you use it out of the tub?

Start with an air pump with a gauge. That way you know exactly what you are doing. With water, you won’t know what the pressure is.


The primary goal of PE should be to make your penis as healthy as possible in both form and function. If you do that, increased size will follow.

Hate it when the nuts get sucked in.


The great elm.

Originally Posted by ellm

Hate it when the nuts get sucked in.

Tie a piece of bandage around your nuts. That normally stops them!


Don't be a lurker left out in the cold. :lurk: Join the happy band of donors!

Psst! The link is at the bottom of the page :bigwink:

If your nuts are getting sucked in, wouldn’t your cylinder be considered too big?


In search of a perfect body, penis, and girl.

The search NO longer continues. :)

Originally Posted by Thick Cock
If your nuts are getting sucked in, wouldn’t your cylinder be considered too big?

is that suppose to be sarcastic? 0.o

Originally Posted by gprent
Start with an air pump with a gauge. That way you know exactly what you are doing. With water, you won’t know what the pressure is.

Alright, I will probably do that. I just dont want that “cone” shaped dick. bigger head than shaft. Does that happen to people who have been pumping for a while?

Originally Posted by wannabebig87
Alright, I will probably do that. I just dont want that “cone” shaped dick. bigger head than shaft. Does that happen to people who have been pumping for a while?

No, that does not usually happen. The head is usually the hardest area to make gains in.


The primary goal of PE should be to make your penis as healthy as possible in both form and function. If you do that, increased size will follow.

Originally Posted by wannabebig87

is that suppose to be sarcastic? 0.o

No, I read it either in pumping 101 or a post from peforeal I forget.


In search of a perfect body, penis, and girl.

The search NO longer continues. :)

Top
12

All times are GMT. The time now is 10:16 PM.