Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Got my pump from lapdist

Got my pump from lapdist

I got it today but I can’t manage to get a good pump that stays.

I got to 3-4hg once and feeled nice pressure, comfortable, but it was all gone 10seconds later.

How do you get a good air seal ?

Keep the hairs short and use a lubricant. :)

Don’t expect a perfect seal though, I usually have to keep adjusting the vacuum as the pressure escapes the tube very gradually.

Check the fitting on the top of the tube, they tend to be loose on new tubes. Add some teflon tape and tighten securely, but don’t overtighten and crack your tube. Also, if you have the removable hose setup, make sure that you hear a click when putting the hose into the fitting on top of the tube. Keep the small O-ring lubricated also, with some type of lube that doesn’t eat rubber.


Penis Enlargement Forum -- How To Jelq -- Free Penis Enlargement Videos

Make a Donation This place runs on donations, help out if you can. Thanks.

Thanks Thunders, you were right, the top of the tube was not tight enough.

Now I’m gonna start a training journal to keep everything recorded.

About this Teflon Tape? Do you put it around this part that I’ve pointed out in the picture below?

cylinder.webp
(7.9 KB, 158 views)

I'm pissed of with my gains and loses. I've been doing this for more than 4 years. I keep measuring wrong and the next time I update my signature you will see impressive results.

Marco,

If the fitting is loose where it threads into the tube, then you can simply tighten it down or remove the fitting and wrap a little teflon tape around the threads of the fitting and then tighten it down. It may have teflon tape on the threaded part already. The tape does not go into the open end of the fitting though, just around the threads.


Penis Enlargement Forum -- How To Jelq -- Free Penis Enlargement Videos

Make a Donation This place runs on donations, help out if you can. Thanks.

Thanks!


I'm pissed of with my gains and loses. I've been doing this for more than 4 years. I keep measuring wrong and the next time I update my signature you will see impressive results.

Are there any Aussies here who know where to get a good pump from in Australia?

Was going to order the lapdist pump but with shipping that is $175 US or somewhere around $230 AUD which on top of the VacHanger I recently ordered is really stretching the old budget.

Guess I can go check out some sex shops but don’t know whether they are any good, people seem to like this pump in particular.
I am 6 long 5 or so girth so was going to go with the 9/2 cylinder. Sound ok?

Measure your girth accurately at the base and let me know. If you are going to spend that much money, you ought to get it right.

At the base I am about 4.75. My glans is actually the girthiest at about 5.25 (more on a good day and can come pretty close to packing a tube with my glans not shaft though) which makes for an interesting looking cock no doubt. Hoping the Vachanger will bring out some of the old inner penis.

I have a cheap pump now without a gauge and it is 2in in diameter and I don’t have any problems with it apart from a little bit of skin suck. Just need something with a gauge and of good quality so I can be a bit more “scientific” and something for the longer term.

Found some on sex shops online here in Oz with gauges for around $100-150 max AUD but no-one I can find gives dimensions of the cylinder.

Cheers gprent

Something is not quite adding up for me with your existing cylinder. Is that 2” diameter an ID or OD measurement? Because a 2” ID cylinder will take you up to almost 6.5 girth and I don’t see how your glans is coming close to packing that.

Guess its OD from one side to another including some small amounts of plastic. I dont pack it at all but gets alot closer then shaft does but there is daylight between me and the cylinder allround. My glans responds whilst in the pump re getting girthier/larger then the rest as well.

Originally Posted by slapa
Are there any Aussies here who know where to get a good pump from in Australia?

Was going to order the lapdist pump but with shipping that is $175 US or somewhere around $230 AUD which on top of the VacHanger I recently ordered is really stretching the old budget.

Guess I can go check out some sex shops but don’t know whether they are any good, people seem to like this pump in particular.
I am 6 long 5 or so girth so was going to go with the 9/2 cylinder. Sound ok?

If you still want a good place to start with cylinders, try toolshed. They are in Sydney on Oxford St.
I picked mine up from there and I wished that I would have went there in the first place.
I think the website is The Toolshed - Great service guaranteed! – The Toolshed AU

Thanks Godzuki, they are very expensive though arent they!

Slapa,

It is quite expensive at $170 for the cylinder but then again it’s going to be worth it in the long run when you have a big penis between your legs.

I’ve only had a few sessions and I like what I see through the cylinder.

I’m starting to fill the cylinder at the base and up the shaft only about an inch but it’s a start.

Before I used to have another cylinder which was totally the wrong size and I could not get much expansion at all.

To me, it’s $170 well spent.

Top
Similar Threads 
ThreadStarterForumRepliesLast Post
Homemade pump: more user friendly with innertubesJosh 14-11Penis Pumps1107-10-2014 12:21 PM
J Meister's Late Night Pump RoutineJ MeisterPenis Pumps1907-05-2007 05:32 AM
Attention electric pump users ? Which is the best electric pump ?etherosPenis Pumps409-22-2005 05:47 PM
Premium pump distinctionscitizen245Penis Pumps103-23-2005 03:11 AM
CTC XL-3000 pump and Lapdist tubeSourmangoPenis Pumps810-14-2004 07:34 PM

All times are GMT. The time now is 12:41 PM.