Am I on target?

Hi guys!

So I’m finally ordering a pump, things are still pretty chaotic…but I think that will be a running theme in my life.

Anyway, I was scanning the posts and I just wanted to check if I ordering the right stuff.

Currently: 7.75 x 5.1 (uniform along the whole shaft)

I need girth, badly!

(and a bit more length)

So it looks like an LA Pump Deluxe measuring 1 3/4” diameter and 11 inches in length.

Correct?

(I have a little bit of a mushroom head)

Thanks guys, and if anyone knows, I’m ordering the pump from California, I’m in Nevada, how long will it take to reach me?

Cheers!
N.

(I was going to continue with my manual efforts untill I made 8 inches…but I’m getting bored, and when I look at the big gainers, again most of the time a pump has been used. I really think that a blast, pump, jelq, squeeze, homedic wrap is the ticket. Along with 5 grams of Arginine, morning and night.)

I would go for a 2” diameter. A 1.75 would be fine for a couple of weeks, but after that you are going to wish you had a 2. A 1.75” diameter would be a circumference of about 5.5 inches. At 5.1 alread and a mushroom head, that isn’t enough room to grow. You could pack that pretty easily and get some good length gains, but at 7.75 you aren’t really hurting in that department. Pumping is fun, and you might consider getting a bunch of different tubes, one for length, one for girth and one for balls.

At 5.1 girth, you should have penis diameter of about 1.62 and thats only .13 from the diameter of your new pump. These dimensions will allow you to max the pump cylinder fairly quickly and set yourself up real nice for length gains, however since its girth you are really after, if it were me, I would go with a 1 7/8 diameter pump. It seems that you already have some decent length there and I agree that you need the girth for good overall proportion. Thats my opinion.

Hey, thanks for the response.

Yah, I always wanted 8”, but having read a number of posts…girth seems to be the thing. If I get much longer at my current proportions, I might be considered a pencil dick.

Not sexy.

Hmm…LAPD doesn’t have 1 7/8, so I think I’ll go for the 2”.

I’ll just have to grow!

Cheers!
N.

(What actually solidified my decision was a recent post in the main member forum from a chap who pumped and has 6.5” in girth…)

2 inches is nearly 1/2 longer than your current diameter and it will probably still work for you if you manage to get a good seal but my experience has shown me that its not so easy with that size difference. As a general rule of thumb, you should not go more than 1/4 above your current diameter for an efficient pump otherwise you may have problems getting a proper seal however if you manage to work it up and max that size cylinder, you will most certainly have some nice girth. Some pumpers that can afford it will buy their Pumps in 1/8 or 1/4 increments in order to make faster gains. I know that there is place that offers them but I cant think of it off hand right now.

Go for the 2” diameter for sure.

I would not advise getting too big. If you start with a 1 7/8 that would be better than a 2 inch. I have both but like the smaller tube better and I am over 6 inch girth. I like to fill the tube and get both the encouragment for length with girth. IOWA

Hi all,

I’ve been looking for a tube size of 1 5/8” ID. I currently have a 1 .75” LA pump and pumping for 4 months now can almost pack the tube, but not quite.

Anyway, would like to get my hands on an inbetween size to work the length more. I started out hitting around 5 7/8” in the tube, now hitting 6.25” - 6 3/8” after a 45 min session, not to bad! Hope to see 6.5” or more in a month or so.

Thanks for any help on manufactures.

ineed9