1st Air pump advice

Hi everyone
I have had a bathmate for around 18months now but the valve is starting to play up and id like to switch to dry pumping.
Everytime i read about pumping i see people making there own buyin all the pieces ect ect.

What i would like is a good pump that comes complete with everything needed to start. Ive heard of various brands and i quite like the drywall? Pump. Also it is in the uk too.

Ive heard that the drywall pumps are more for length than girth because they fit fairly tight to the shaft with little room either side….is this true?

I am trying with all my might to gain girth mainly and just wanted any opinions on the best brands. My budget would be approx 80-120 pounds.

Any info welcome

Thanks

I got my leluv setup for $70 it works great

Amazon if a great place to get a decent starter set up. I get all my pe stuff from amazon.

Ive had a look and really like the vacutech pumps purchased complete. I may have to contact them as there size guide has my size missing and it falls between 2 size categories.

Has anybody got any advice on which typd of cylinder is best, im looking for girth mainly but length is welcome too?
Most popular cylinder length is 9 inches which sounds abit over the top? Im 7.3bpel max and surely it makes sense to pack the tube as much as possible and not have a couple inches spare at the end?

Lastly any gains anybody has made from dry pumping is welcome for motivation haha thanks

Good morning.
Make sure you did not purchase the wrong size of cylinder: Selecting Your Cylinder Size. A 9" cylinder should do it, length-wise. Tighter tube stimulate length gains, so you will need room girth-wise to increase your circunference.

More than a few people actually, here is part of them that I know of, there is more pumpers for sure: (gprent, avocet8, Mr. Happy, supersizeit, Titleist, pumpbra, BaddJack, iLogPE, bluray, irishjim, dtwarren1942, oz) and I’m one of them. I’m pumping for a little less than 6 months and quite happy with it, very addictive.

To me it’s the safest and easiest way to grow. Make sure you’re using constant heat.

Fantastic replies guys thankyou and i shall proceed to buy as my bm is giving up on me!!
As for the cylinder size do u guys recomment getting the cylinder size that they advise? Currently im 5.2 beg 4.8meg and 4.5 behind the glans. This puts me inbetween 2 sizes on their chart the size below is too tight and next size up sounds abit too roomy.

I agree pumping is addictive i loved my bm and whilst not made great gains ive always stuck religiously to my routines. I will use heat for sure.

Sorry, what is “bm”? Keep your posts as clean as possible, without abreviations and the most formal as you can get Forum Guidelines . For us that english ain’t our main language, sometimes can get a little tricky to understand, appreciated.

If you choose the 1.75” cylinder, your base girth is already too much for it, and in no time, mid-shaft will pack really quickly. I think the best bet, in your case, is the 2.00”.

Sorry useless the abbreviation was for bathmate. I will keep it clean :/

When people talk about packing the tube and needing the next size up does this mean you are actually getting the gains or just more expansion in the tube? When i clamp with heat i get massive expansion at the base and the underside (the cc?) Really expands however this hasnt seemed to translate into base gains yet.

That expansion, sooner or later, will become permanent. With a bigger cylinder the girth expansion wont be limited by the tube.

While pumping creates negative pressure coming from “outside” of the penis, acting alot on the skin … at clamping the pressure comes from “inside” the penis and it is determined by how tight you setup the clamp and to how much and/or how strong you kegel while at it.

Remember that PE creates micro-tears, so the growth and gains takes time.

With 4.8” MSEG, in my opinion, a 1.75 cylinder would be more appropriate. I did not move up to a 2” cylinder until my MSEG reached over 5”. I am currently 5.5” MSEG and I am only packing the first half of my 2” cylinder. I believe if your erection had an even girth throughout, the 2” cylinder would be ok. But since you have a tapered erection, the 1.75 would better serve you, although you may need to upsize after six months.

I think you mean Thickwall, not Drywall :) Their stuff is very good. With the shape of your penis, I’d likely go for the 1.75” too, especially if you get it from Thickwall, as they are actually just slightly bigger than 1.75”, which is better still. :)

I’d second this.
If you’re in the UK I don’t think you can do better than Thickwall, their Cylinders are quality handmade.
Vacutech stuff is great as well but you get hammered by shipping, tax and import duty.

Don’t use any oil based lubes like vaseline on them and they’ll last for years.

Ain’t his base girth of 5.2” is quite large for 1.75”?
I’m at 4.9” base girth and the 1.75” (LeLuv) get base packed really quick (most of it is skin being sucked from the body).

1.75” = 44.45mm
44.45mm x 3.14 = 139.5mm circumference = 5.49”

So the maximum girth you can reach in a 1.75” tube is 5.49”.
Packing the base isn’t a problem as it helps create a better seal. With a 4.8 mid girth there is still quite a way to go to pack a cylinder that will allow a 5.5” girth, unless you are prone to a lot of lymphatic bloat.
Having a lot more ‘air space’ in the cylinder means that you have to do more pumping to remove the air, which is not a problem if you are just pumping to the vacuum you want then disconnecting the hose and leaving it at that level, but if you are pumping up, then releasing most of the vacuum, then pumping up again multiple times, it’s easier to not have too big a cylinder.
I still recommend having a minimum 2” extra cylinder length over erection length though.