I got The BIB Hanger, BUT I HAVE PROBLEMS!!!

Guys, I need your help! I just got the BIB Starter, super happy, but then I tried to use it and it was hell!!!!

I am just coming from a 1 hr session in the bathroom where I failed at all my attempts. I feel so frustrated.

First of all, I am really having a hard time to keep my skin pulled back while trying to wrap the penis. I just can’t do the two things at the same time.

Then, when (and if) I finally manage to do that, it takes me hours to close all the little screws of the hanger, and while I do that, inevitably the skin goes back to the front.

When finally I do close all the screws, I hang the weights, but because the skin in the meantime has gone to the front, I feel the major pulling at the skin and it hurts. I am not cut but I am naturally….which means that I have short skin naturally, my penis does not close completely.

And, to make things even worst, while I try do do all those things with two hands, I realise that the blood has gone back to the head!!!!!!

HELP!!!!! I feel like I want to throw everything in the garbage (no offense BIB, it’s not a critique to your thing, I like it, it’s just my penis I guess)

Please help me…it’s so frustrating. How do I do all those actions at once? The blood will inevitably go to the head while I do the other things…

I hope I can do it, I really hope. Any help is REALLY appreciated.

Thank you

mr,

>I am just coming from a 1 hr session in the bathroom where I failed at all my attempts. I feel so frustrated. <

I can be frustrating at first, don’t worry.

>First of all, I am really having a hard time to keep my skin pulled back while trying to wrap the penis. I just can’t do the two things at the same time. <

Are you uncut? If you aer uncut and talking about the foreskin, leave it over the head.

>Then, when (and if) I finally manage to do that, it takes me hours to close all the little screws of the hanger, and while I do that, inevitably the skin goes back to the front.<

You say screws. The side with two wing nuts should be fully tightened before you attempt to hang. The only side you tighten when you are actually hanging is the front side, with only one screw.

>When finally I do close all the screws, I hang the weights, but because the skin in the meantime has gone to the front, I feel the major pulling at the skin and it hurts. I am not cut but I am naturally….which means that I have short skin naturally, my penis does not close completely.<

Ah I see. The problem here must be the wrap. If the wrap was correct, it would hold the skin in place for you while you tighten the hanger. Did you read the ‘wrapping diagrams’ thread?

Remember that when you put the hanger in, the shaft needs to be low, close to the hinge. Then close the two halves, hook the screw in and spin it down so that it is ‘on’ but not tight yet. Then make sure the shaft is still low (avoid contact with the tightening screw, as the top of the shaft behind the head is a delicate area, with nerves and stuff), push it down if it is not, then finish tightening.

>And, to make things even worst, while I try do do all those things with two hands, I realise that the blood has gone back to the head!!!!!! <

Three hands would be useful. Just squeeze the blood out. Try the suggestsions above, I think this problem will not arise. The main thing is the screws. This is from the product guide:

“Remove the hanger from your penis, and completely loosen the two wing nuts on the hanger’s right skid. Pull the right skid away from the hinge. You will find two sets of nuts. The nuts immediately next to the hinge are used to attach the bolts to the hinge. DO NOT LOOSEN THESE NUTS. The nuts adjacent to these nuts are the adjustment nuts. There are two, one at the front and one at the rear of the hanger.

Place the shaft of your penis in the shaft well, close the hanger, and estimate the amount of gap needed on the bottom. The bottom gap should be equal to or slightly greater than the top gap. Unscrew the adjustment nuts as necessary to create the appropriate gap. Then retighten both wing nuts.”

SS4

mrfuturo,

Don’t give up. It has taken my a awhile to get anyway close to comfortable with the Bib hanger. I have both the regular and the startor.

Some people can get it right from the get go but not me. It takes practice if your like me. Hell I still don’t think I am getting it (wrapping and attachment) done correctly but I am getting better at it.

So don’t stress mate. Your are not the only one out there.

GMJ

mrfuturo,

SS4 is the uncut king. Listen to him. He is correct, get your wrapping correct first, then get the adjustments on the hanger close to correct, then try to hang.

The bottom two wing nuts have to be tight before you apply the hanger. Only the top tightening bolt is tightened when you apply the hanger.

Also, when you first put on the hanger, before tightening all the way, you can push it forward to release the trapped blood in the head. If this does not work, then you have wrapped too tight.

Bigger

If you haven’t got 3 hands try using a length or string tied to something solid with a noose to hold your bellend straight out while you wrap. That’s what I do -just be very careful what material you use and how you attach it. It doesn’t have to be tight (and whatever you do, don’t fall backwards!)

It took me ages to get the hang of wrapping and I’m still trying to perfect my technique. I remember well how I used to struggle & curse to hold the bolt & washer out of the way while I tried to get the hanger into the right position whilst at the same time holding the bellend out. I’m sure you will soon get the hang of it and will wonder what all the fuss was about :)