Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Chicken choker vs. Captain's wench

1234

CAUTION: Do not attempt 30 min. sets unless the head of the penis still feels warm after 20 min. Remember, tissue death starts to occur 17 min. after circulation is cut off. Always monitor what’s happening down there while hanging with any device. Also just because it feels warm at 20 min. with 7 lbs. doesn’t mean the same thing will happen at 10 lbs.

Personally, my longest set was 23 min. at 14 lbs. I stopped the set because the head felt too cold or I was getting some discomfort to the shaft.


Starting: 5 BPEL x 4.5 EG on 4/19/03

Latest: 6 BPEL x 5 EG on 2/17/04

Goal: 7 BPEL x 6 EG

CC,

So much for my bold “plateau buster” plan!

I can get to 20 min easy, no problems at all. Once I hit 24-25 though, things went down hill, FAST!

My head starting getting cold and discoloured so I stopped straight away.

I didn’t get as fatigued as I would have liked -I dropped from 7 - 5 -4 and then stopped- but nice and sore ligs this morning so mission accomplished I guess.

Good enough, Andrew!

You still pushed the envelope and you monitored it well.

Have a nice day.
:)


Starting: 5 BPEL x 4.5 EG on 4/19/03

Latest: 6 BPEL x 5 EG on 2/17/04

Goal: 7 BPEL x 6 EG

Where do I start?? Being new and all.

Originally Posted by get big
Where do I start?? Being new and all.

Since that was your first post, WELCOME TO THE BOARD! THE HOLY LAND OF PENIS ENLARGEMENT!

I recommend you start at the Newbie Forum. Then, after several weeks, you may want to get into hanging ( in my opinion you should ). I then recommend my special thread:

Oh looky here! The CCH3.

You can also check out the Hanging 101 thread at the top of this forum.

Good Luck
:)


Starting: 5 BPEL x 4.5 EG on 4/19/03

Latest: 6 BPEL x 5 EG on 2/17/04

Goal: 7 BPEL x 6 EG

Damn, now I want to get a CCHO3. Wench is good and all to get started, but CCHO3 seems better for longterm hanging. But it is complicated to make with all the cutting. I’m going to see what I can do though, because my head gets cold after like 10-15 min of hanging with the Wench.

It does take around 45 min. once you have the 3 inch pillars cut from the main PVC pipe.

Use 4” pillars if your erect girth is over 6”.

Hey, what’s a bit more work for your one and only best friend in the world?
;)


Starting: 5 BPEL x 4.5 EG on 4/19/03

Latest: 6 BPEL x 5 EG on 2/17/04

Goal: 7 BPEL x 6 EG

Ok, I’m just having trouble understanding the cutting part of the pillar. Aren’t the PVC pipes made out of real hard material. A typical knife would have trouble with that. Also, the red dots in the picture. I didn’t understand how you determined where to place them. That and this one step here.

2. Bevel the longitudinal edges so that the gripper pads lay flat against them.
Notice the beveling in the photo.

What longitudinal edges?

My last question is, you don’t need any wrap? Or less than usual.

Originally Posted by Supremeone
Ok, I’m just having trouble understanding the cutting part of the pillar. Aren’t the PVC pipes made out of real hard material. A typical knife would have trouble with that.

That’s why you use a power drill and drill out the outline of the windows. Then you use a ( Swiss Army type ) knife to cut through the tiny holes you just drilled.

Quote
Also, the red dots in the picture. I didn’t understand how you determined where to place them.

Once you cut out the windows, pick out just one of the 2 longitudinal edges of each window and place a red dot above and below that edge.

Quote
What longitudinal edges?

The edges of the windows that are parallel to the long axis of the pillars themselves.

Notice that the windows each have 4 edges. There are 2 that are near the ends of the pillars. NOT THOSE EDGES, but the other ones.


Starting: 5 BPEL x 4.5 EG on 4/19/03

Latest: 6 BPEL x 5 EG on 2/17/04

Goal: 7 BPEL x 6 EG

Top
1234

All times are GMT. The time now is 05:27 PM.