Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Bib hanger

123

Originally Posted by mochaman
I keep stripping the top bolt out.The bolt diameters used on the Bib Starter seem to be too small to hold the force that is created with higher weights.

I’ve used the recommended Vaseline on them to keep them lubed.

Larger diameter bolts with deeper & stronger threads would prevent the frequent stripping of the top bolt.The bottom bolts hold up since there is two of them to spread out the force from heavy weight ” 14 Pounds”

Have you tried using your opposing hand to close the hanger and then turn the wing nut vs having the wing nut close the hanger. This way the tension is not on the threads.

The other option is switching out the bolt with stainless steel, or grade 8 (if that is available at that size).


12/11/2013 BPEL 5 3/4 NBPEL 5 1/16 BPFSL 6 1/16 NBPFSL 5, EG Base 5 EG Mid 4 7/8 EG Below Glans 4 3/4

11/02/15 BPEL 7 1/8”, BPFSL 8 1/16”, EG Mid 5 1/4 —- Goals BPEL 7 1/2”, NBPEL 6 1/2", BPFSL 9” Motivational Resources Wanted

8/9/2014 259 lbs ---- 11/2/15 248 lbs 33.2% body fat Bhcentral's Progress Reports and Pictures

I’m getting by without having to tighten the top bolt.I have the top bolt pre- tightened,I then manually squeeze the hanger ,latch the top bolt in then tighten the bottom bolts.

I’m going to try & find a better bolt if one exist.Ideally you should be able to tighten the top bolt without it stripping.

Yeah it is just the repeated friction of set after set. Most of those bolts where not designed for that.

Vaseline helps and then once you feel that you need to apply heavy torque just manually close hanger and finish up wing nut with less torque.


12/11/2013 BPEL 5 3/4 NBPEL 5 1/16 BPFSL 6 1/16 NBPFSL 5, EG Base 5 EG Mid 4 7/8 EG Below Glans 4 3/4

11/02/15 BPEL 7 1/8”, BPFSL 8 1/16”, EG Mid 5 1/4 —- Goals BPEL 7 1/2”, NBPEL 6 1/2", BPFSL 9” Motivational Resources Wanted

8/9/2014 259 lbs ---- 11/2/15 248 lbs 33.2% body fat Bhcentral's Progress Reports and Pictures

Update on top bolt constantly stripping out on BIB Hanger :

I was able to change the stock # 8 bolt to a thicker #10 bolt.This fixed the problem of the top bolt stripping out prematurely.

Can you give length dimension offhand?

The BIB Hanger comes with #8 machine screws three inches long.Screws / Bolts under 1/4 inch diameter have a numbering system.I replaced the #8 three inch long machine screw with a #10 three inch long machine screw.The machine screws come in a pack of 3 at HD /Lowes.I also had to get a pack of new wing nuts & washers for the new size of screw.

Excuse my ignorance, but where do I buy a Bib hanger and how much do they go for? I am going to Hang/W-Pump/Jelq for 6 months. I don’t have tools to build my own either.

Originally Posted by AllKnighter
Excuse my ignorance, but where do I buy a Bib hanger and how much do they go for? I am going to Hang/W-Pump/Jelq for 6 months. I don’t have tools to build my own either.

http://www.bibhanger.com/

Top
123

All times are GMT. The time now is 10:58 AM.