The SuckXtender - just remember it sucks!

Here’s hoping it does too! Wow, very impressive gains. Is EL moving for you too?

Xeno, over 15 months (before using this stretcher) my BPEL has grown at a steady rate of 0.3” p.a. I haven’t measured any increase in the rate of growth yet.

Looking at the initial results on my BPFSL of using the stretcher the rate of increase in my flaccid length seems to be six times greater!

The way I look at it three things can happen -

1) over the coming months my BPEL is going to increase more rapidly
2) the present rate of increase in my BPFSL is going to drop off rapidly
3) if neither 1) or 2) happens then I’ll end up with a massive flaccid penis that shrinks when it gets hard! :)

Makes sense to me.

Based on the rate increase in your BPFSL, I think we can be optimistic for option 1 to occur.

Lets hope option 2 doesn’t occur until your satisfied with the results from option 1!

I don’t want to contemplate option 3.

Is 3) even physically possible?

It doesnt bear thinking about!

Week 3 - LegXtender (i.e. the bungy)

…………..Hrs “up” Hrs”down” Weekly Hrs Cumulative Hrs BPFSL Before After

Week 1……..0……….12…………12………….. . 12………………..6.9”……6.9”
Week 2……..0……….12…………12………….. . 24………………..6.9”……6.9”
Week 3……..0……….13…………13………….. . 37………………..6.9”……7.0”

First increase… I was starting to wonder.

Note: stretching is done in stealth, no heat used.

Hello, I don’t know how to begin?

If you mean begin with PE, read this first:

A Newbie Primer

If you mean something else, please clarify the question.

What a wonderful device you gentleman have created here.

I do have some questions, possibly redundant/stupid questions, for this I do apologize. But please keep in mind that I am a woman, and I don’t have a penis. Well I do, but it’s attached to someone else.

Anyway, I noticed in your pictures that when you were using the weight, it appeared that the stretch is mainly at the bottom half of the shaft? Is this were the pull is mostly or does it go throughout the shaft, and does it even really matter as to where the “pull” is?

Another thing, is this device easily constructable, especially as far as time goes. I can see that the Legstretcher does look fairly easy to construct.

We were considering purchasing a device, time issues, but cost has pretty much eliminated that for know.

The remainder of my questions pretty much are concerned with such things as any injury’s, discolorations, and the like?

OK, guys, I got all the stuff I needed for the SuckXtender. One problem though. My glans won’t fit into the film case. Just a quick question. Are film containers bigger for more exposures? I got a 12 exposure roll. Will a 36 exposure roll be bigger or no? If not I need to find something else. What a bumber I was all set to finally get it done. :(

Nope, film canister is a standard size regardless of exposures. I’ve got a similar problem, I’ve got very little flacid girth, but a pretty fat head and can’t squeeze it into a canister without major stuffing (which causes the glans to swell a bit more) and I end up with a large air pocket at the bottom of the canister.

I found an air-freshener cap that seems to be the perfect size, wider than a canister, but not quite as deep. Seems to fit my glans much better.

I was afraid of that. Thanks Eroset. That cap looks a little big for me. Now to start my search. I think I’ll need something around 1 3/4 - 2 inches in diameter. If anyone has any suggestions please feel free to chime in.

Hey CrazyLady,

I’ll try my best to answer these. The device pretty much pulls evenly on the shaft. There may be some more pressure down by the base, but it is pretty uniform.

The LegXtender is pretty easy. It took me about 20 minutes and that was with getting all the supplies and tools together. (I did this before even thinking about trying the size of the canister….oops!) I also constructed the stretcher portion of the SuckXtender. THat only took me another 15 minutes to put together. Now, I will use my LegXtender on the stretcher. I bought a metal plate and drilled three holes in it. One in the middle and two on either side. This way I can interchange the flat plate (for the strtcher) and the angle bracket (for the LegXtender) by just removing the nut and swapping them. So in total I spent about $10 and 40 minutes to get everything finished. I hope I explained things clearly.

That cap is just slightly larger in diameter than the film canister. The film canister just manages to fit inside it, so it might actually be on the small size for you. I believe that I measured it at 1 3/8” It’s also a little flexible so I can squeeze it into a slight oval shape to get the glans in comfortably, then let go and it returns to normal.

For a while there, I was just wandering around the house, shoving my member into just about anything that looked the right size. The wife was kinda worried about me for a while.

:rofl: That made me spew my water everywhere dude. Thanks!

Yeah. I don’t know what I was smoking when I wrote that last post. I need something in the 1 3/8 - 1 1/2 inch range. SO what you have there may work perfectly. I’ll have to go to Walmart and look for that. Thanks for the help!

I positively NEVER though I’d hear that from a woman! Why thank you!

Injuries - none recorded yet, with the exception of lymph buildup in the glans (see “stretcher pictures” for that). Seems that if one uses the vacuum device in 1-hour stints with 10 minute rests inbetween this is avoided.

Discoloration - none yet, except temporary deep reddenning on the glans after having had it on for >2 hrs.

The like - none recorded yet. Except possibly that you want to make sure you have something comfortable as a leg strap, the velcro will chafe like crazy otherwise.

Feel free to ask more, of course.

Oh, by the way, RTG’s price qoute was not entirely accurate - the full cost is materials + $10 royalty, care of Thunder’s Place (just send it as a donation!).