Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Post your penis width.

Ok so I busted out the callipers…

Base width (half an inch from pubic bone) = 1.45 inches

Mid width = 1.5 inches

Top width (just below glans) = 1.61 inches

For the record, my girth is between 4.4-4.7 inches depending on where its measured. A pretty skinny penis :(

2” wide, 5.5” mid-shaft EG, 6” base EG


If girth is king, why the hell does everyone keep talking about length?

1.5 inches mid shaft.


4Foreskin ;)

Just hair over 2 inches…6 inches in girth.

Are obviously these measurement taken with a rigid ruler, but the definite measure should need a caliber!

:lisa:

Girth

HI GUYS 1 3/4 across 51/4 around, cut , shaved LOL

Originally Posted by ventitre
Are obviously these measurement taken with a rigid ruler, but the definite measure should need a caliber!
:Lisa:

Yeah, a rigid ruler here.

Not particularly accurate.


Starting stats:- Dec11th2008 7.2"bpelx6" meg.Mar23rd09 8.375"bpel x 6.125"meg. Mar10 8.4" bpelx6.125" meg.

Goal: 8"nbpel x 7" A one eyed monster by any standard :)

It’s accurate if you line up your shaft perpendicularly with the ruler on both sides(with one eye of course).


Decemeber 2007: 5.8" BPEL x 4.9" MSEG

Current:-------->7.7" BPEL x 5.7" MSEG (7.2" NBPEL)

Current Goal:--->7.6" BPEL X 5.8" MSEG Do or do not, there is no "try".

Originally Posted by fendool
Ok so I busted out the callipers…

I started to try this, but that sharp metal was too scary. Would get a nice acurate measurement though.


Current average: NBPEL 7(ish)" / MSEG: 5.25"

ST Goal : NBPEL: 7" / MSEG: 5.5"

LT Goal: NBPEL: 7.25" / MSEG: 6"

Originally Posted by Tweaking

I think it would be better to use two eyes actually, since if you move your head you’ll probably move your hands.

Yeah that’s the tricky part. But I use two hands to keep it as still as I possibly can when I move my head.


Decemeber 2007: 5.8" BPEL x 4.9" MSEG

Current:-------->7.7" BPEL x 5.7" MSEG (7.2" NBPEL)

Current Goal:--->7.6" BPEL X 5.8" MSEG Do or do not, there is no "try".

For the record, I measured a perfect cylinder that has a girth of 6.375.

It measures a tiny bit over 2 ” in all directions (Obviously, because it’s a cylinder).

Just thought I’d share that. I don’t know if that helps anyone’s research.


I’m 6.5 inches across with a girth of 13 inches. That’s right, a shovel head!

Originally Posted by vagabund
Just thought I’d share that. I don’t know if that helps anyone’s research.


I’m 6.5 inches across with a girth of 13 inches. That’s right, a shovel head!


:funpost: Man you’re on a roll.


Decemeber 2007: 5.8" BPEL x 4.9" MSEG

Current:-------->7.7" BPEL x 5.7" MSEG (7.2" NBPEL)

Current Goal:--->7.6" BPEL X 5.8" MSEG Do or do not, there is no "try".

I always thought that I was pretty wide at 2 inches, but from what everyone is posting here I guess not.

HI GUYS , Kinda hard to get a good reading , I figured the best way was to use a hole template that you use for drawing with , then you know exactly what size if it fits in HOLE

Top

All times are GMT. The time now is 09:01 AM.