Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

New auto jelqer design

123

New auto jelqer design

Hello, I have returned with my tail between my legs, but non-the-less ready at another attempt at the auto jelqer. This time I made 3d pictures before I posted, and designed, and designed many different ideas before I came to the conclusion of using this but if you are not familiar with my last attempt I will outline the problems since I never posted them anyway.

Low power output
too much friction
just plain stupid

I will end there and unveil the next design. It is similar to an aperture or an iris. You could call it a sort of a mechanical sphincter. The advantages of this design are a self contained motor and actuator instead of having to transfer power. Plus it has a much higher power ratio because of this. Unfortunately it will be harder to make but I have already contacted prototyping companies and asked about requesting a quote. The actual actuator shouldn’t be harder to make though. Tell me what you think and ask me to explain anything if you need me too.

Another advantage of this is because of it’s circular design it could be used for vacuum jelqing a frontier not yet reached.
One more thing, the linear actuator isn’t shown this is just the designs for the gripper/motor.

AJ ASSEMBLED.webp
(10.8 KB, 505 views)
AJ NOT ASSEMBLEDresized.webp
(14.2 KB, 430 views)

I’m not getting it:) . But I’m routing for you 100% to make a real auto jelqer.


I haven't failed, I've found 10,000 ways that don't work. Thomas Edison (1847-1931)

So, how exactly will this work?


Obsession is a word used by the lazy to describe the dedicated.

My Pics

AOM's training log

It looks awesome. Very nice design, I am assuming springs will provide the tension to close the iris around your penis.

Are you sure that’s not a design for a penile guillotine? Please tell me that’s not metal!


Let me tell you the secret that has led me to my goal: my strength lies solely in my tenacity.

Louis Pasteur

Basically there is an actuating plate that act as guides for the rods (opposite of the pivot point). There are slits that guide the individual petals of the iris so when the pivot points are turned on the middle axis (the very center of the circle) the only way for the pivots to turn is outward without jamming the whole thing. Will make a more detailed animation and a prototype soon. I have already made a rough prototype out of card board and nails, the next one will be more drawn out and more exact so that you guys will be able to understand it better. I will eventually give everyone instructions on how to make the iris so they can understand it. aom91 (and anyone else who was responsive to my last thread) you have seen the old design, I am sure you see how much more elegant this one is then the last.

I will probably have some digital drawings to show more details.

I don’t expect you guys to understand it without more of visual aid, if you do thats great, but if you don’t, I do intend to put up a lot of images and videos.

AJanimation.webp
(3.7 KB, 248 views)

How are you going to get the jelq moving up and than releasing, and at the same time as the release grabbing again at the bottom?


I haven't failed, I've found 10,000 ways that don't work. Thomas Edison (1847-1931)

DO NOT WORRY there will probably be some soft silicon on the edges of the petals, and as for the springs I thought about it, and I am still considering it, but my hope is the motor will be strong enough, I want t keep things from wearing down.

Thunder, it doesn’t use a di-lithium crystals, it uses zero point module, get your futuristic power sources right! (Just joking) But that does bring up a good point, I am not sure how much power it will need, so before I install a permenent AC to DC transformer, I should look up some equations online. Don’t want melted plastic or your dick right?

Originally Posted by Dino9X7

How are you going to get the jelq moving up and than releasing, and at the same time as the release grabbing again at the bottom?

I have some timing pulles pulleys that will do the trick. Go to my old auto jelqer thread and you can see them there. As far as the releasing will go that should just be some simple sensory electronics

Originally Posted by Avogadro6022
DO NOT WORRY there will probably be some soft silicon on the edges of the petals, and as for the springs I thought about it, and I am still considering it, but my hope is the motor will be strong enough, I want t keep things from wearing down.

Thunder, it doesn’t use a di-lithium crystals, it uses zero point module, get your futuristic power sources right! (Just joking) But that does bring up a good point, I am not sure how much power it will need, so before I install a permenent AC to DC transformer, I should look up some equations online. Don’t want melted plastic or your dick right?

Hey, I’m old school. I think that zero point module stuff is causing galactic warming. And nope, having hot molten plastic on my dick is not on my fun list. ;)


Penis Enlargement Forum -- How To Jelq -- Free Penis Enlargement Videos

Make a Donation This place runs on donations, help out if you can. Thanks.

It reminds me of this ancient Chinese war weapon which was used to slice off the head’s of captured prisoners. The mechanics appear to be exactly the same although of course the Chinese version had sharp blades. I hope it doesn’t slice off my dick.

Would you still have to move the device up and down? Personally I would rather use a mechanical device that makes the squeezing easier so my hands don’t get sore as fast while maintaining control over the pressure.

Anyway if it doesn’t work out you can always redesign it as an anti-rape device called pussy iris. Would make prisonlife more bearable as well ;)

Hey I have made some progress with actuating plate, I hope to get a rendering soon, it is taking me along time to get this down though, probably because my 3d modeling program is not what I am use to. status135, what is the name of this device, I would like to see it, maybe it can help me.

EDIT: I think my original actuating plate was the right idea, maybe with a few modifications, I was thinking of something totally different. I may get the materials wednesday to build my wooden and/or paper prototype, if they have plastic or foam I will get that.

Top
123
Similar Threads 
ThreadStarterForumRepliesLast Post
Auto JelqerAvogadro6022Penis Enlargement Basics5406-04-2008 07:04 PM
Hanging RoutineDickstructionPenis Hangers902-07-2006 03:18 AM

All times are GMT. The time now is 09:55 PM.