Cheap Zinger offer

I’ve only tried cock and balls, as I thought the idea was to stimlate the testicles. That said, it would be good to get feedback from a variety of ways, so go with what feels right for you.

I hadn’t considered the above when cutting the tubing up as I made the assumption of C&B. Do you have enough tubing to make both types?

I made mine on friday, thanks Shiver. The tube was slipping off the zinc so I tried to bend it today like the copper. Bad move, the zinc cracked like it was cast iron. It is bent though and still in one piece but it has rough areas exposed. I will have to melt it down or maybe just torch the rough bits to smooth them out with light melting.
I was using it all weekend, it was tight and I got very hard erections which I put down to the cockring effect, but when I took it off they were still rock hard.

People had been putting saline solution in the tubes which was meant to boost the voltage or current. I thought if this (lower resistance between the 2 metals) works why not join them totally. I put the zinc and copper to my tounge very closely and got no effect, but when I touch the 2 rods I get a distinct shock on my tounge. Any electrical minded people know about this?

just found this thread again
Ball zinger - new great (but difficult) idea for boosting voltage

“Except when very pure, zinc is brittle at ordinary temperatures, but malleable at about 100°C, and can then be readily rolled and hence unalloyed wrought zinc is used extensively for fully supported zinc roofing. “

“Zinc is a silvery blue-grey metal with a relatively low melting point (419.5°C) and boiling point (907°C).”

420C is eaily achieved even with a heat gun

Thanks Shiver and trigger got my zinc and copper today.
If there is anything i can do for you guys pm me

Thanks again MM.

Trigger:
I have a couple of MAPP gas torches, and decided before cutting up the rods that I would try to heat the end that had screw thread on it (it arrives with a brass fitting on the end which covers about 1/2” additional rod).

It went from a solid to a blob on the floor faster than you can blink. MAPP gas is very aggressive though, so you might find with something like butane or propane that you can control it better. Also, it seems to absorb and retain heat very readily so I would take my time in bringing it up to temperature, otherwise you might find that you overshoot and end up with a molten pool instead of a rod.

As for the tongue experiment ( :) ) I don’t know. I too would like a definitive answer to this (hence the zinc bars shipping all over the place). I really can’t grasp how creating a battery around something would do anything. If the body is part of the battery (least resistance path) then I have to accept that at least there’s the possibility of something happening.

MM:
You’re welcome.

Thanks for the heads up on the zinc melting. The battery thing has me puzzled. Lick 2 opposite poles of 2x1.5 batteries and there is no zing. Connect the 2 poles and you get a zing. The battery is linked internally by a conductive paste. Seems to me your tongue acts like (very weak) conductive paste both forming the battery and drawing power from the battery, but it seems if the conductive paste is less resistant you get more of a shock.
But if the 2 metals are only joined by conductive paste then a normal battery should be wearing itself out as the 2 poles are joined just like on a zinger, or am I way off there. Time to research batteries…

I posted on the other long zinger thread. How many others noticed a great difference using saline solution.

Perhaps we should move over to the other thread rather than running two in parallel?

Let me get this clear:
You have the two bars. One end of each is on your tongue. Are the other ends touching too?

You say that you feel nothing until they touch together. Is this on the tongue end? and if so, what about if they were only 1mm apart? Could it be the resistance is too great to feel? Could saliva or something is making the connection whilst bypassing the nerves?

Hang on, why don’t I try it….[fiddles about a bit]

Some time later:

Okay, I found that if I hold the two parts, I get no feedback until they connect. At that time there would be a small battery running from the zinc tip, through the tongue to the copper then back to the zinc.

If I connect the other two ends with wire, then I can apply them to the tongue with a gap and still get the tingle. Just touching the other two ends doesn’t seem to be as effective as with a proper wire.