Is LENGTH only limited to the deformation of the tunica? If so are the collagenous fibers regenerating to undergo more deformation?
02-10-09: Nbpel-4 7/8" ; Midshaft-eg- 5 1/4"; Base-eg- 4 7/8"
ponyLok
Benefits of Heat in PE
seahorse
Originally Posted by Shiver
This might sound stupid as I’ve never used a pump, but could a pump be filled with a gel rather than air? (to provide a heat mediator when a pad was wrapped around the pump).
Pumping doesn’t pump air in, in our case, it pumps it out causing a vacuum. I would imagine gel, like water, could get into the system and would call for a trap to be fitted, however, I can’t see what value gel would have?
petitfaun
Originally Posted by seahorse
Pumping doesn’t pump air in, in our case, it pumps it out causing a vacuum. I would imagine gel, like water, could get into the system and would call for a trap to be fitted, however, I can’t see what value gel would have?
The consideration was that the gel would act as aheat insulator inside the tube and in direct contact with the penis and keep it warmed by preventing heat loss. But water would probably be much better; as with gel there would be cleanliness problems
Don't be a lurker left out in the cold. :lurk: Join the happy band of donors!
Psst! The link is at the bottom of the page :bigwink:
JackovDiamond
Originally Posted by dongalong
I use my Thermotex wrist pad to give constant heat during my stretching routine.
It’s size is 8”x2”, so depending in my stretching angle, I manage to heat up most of the shaft without interfering with my grip simply by covering the exposed part.
The heating element is a flat plate so it doesn’t wrap around the shaft but since far infra red rays penetrate up to 3.5” into the skin, it does the job perfectly and saves time because reheating isn’t required between holds
I tried to buy one of these the other day but something was amiss with Amazon market place. But that’s a side issue. You mentioned earlier in this thread that you were concerned the bars/rods on your extender would heat too much but it wasn’t a problem, I use a Vacu-hanger and will use the wrist pad while I hang, I’m concerned that it will heat the silicone sleeve, possibly deform it. Is this likely?
Thank you
ItzGrowing
Can’t believe i just found this thread. Went out tonight and got an infrared lamp and immediately saw an 1/8” increase in flaccid stretched length. Only time will tell what if any permanent gain comes from it, but I find it encouraging.
Started: BPEL 6.75" MSEG 4.75", Now: BPEL 7.75" MSEG 5.438", Goal: BPEL 8" MSEG 6"
GFang
Originally Posted by SixPackofBud
Can’t believe I just found this thread. Went out tonight and got an infrared lamp and immediately saw an 1/8” increase in flaccid stretched length. Only time will tell what if any permanent gain comes from it, but I find it encouraging.
Ditto, I began using stretching with an infrared lamp about 3 weeks ago, and have increased my flaccid length by about 1/2” so far. My stretching consists of 1 hand pulling outward, 1 hand pulling inward, for about 15 minutes per day. Infrared doesn’t come without disadvantages (bulky, uneven heat), but it’s given my cock invigorating penetrating heat. I likely won’t go back to rice socks or dipping my wang in hot water.
Note- I bought the brooder off Amazon ($12) and the 250W bulb from Home Depot ($10).
ashiato
Originally Posted by oldman77
I was wondering the same thing about Icy-Hot. Seems resonable, but not sure if it would help or not.
Good god no. The sensation of heat and heat are two completely different things. Icy-Hot gives you the former without the latter.. the latter is what is necessary for the benefits described here.
2009-05-20: 6.5 x 4.8 - Starting Stats
Short Term Goal: 7 x 5
Long Term Goal: 8.5 x 6.5
ugaribe
Very nice thread! Thanks for the information!
Shiver
Wow, can’t believe this thread is over 6 years old now. Sounds like you guys have been having some success.
Shiver
TheLawnmowerman
Originally Posted by oldman77
Quote
I was wondering the same thing about Icy-Hot. Seems resonable, but not sure if it would help or not.
:eek2:
petitfaun
Originally Posted by Shiver
Wow, can’t believe this thread is over 6 years old now. Sounds like you guys have been having some success.
Shiver
Hey! Good to her from you Shiver. Are you back in the UK now?
Don't be a lurker left out in the cold. :lurk: Join the happy band of donors!
Psst! The link is at the bottom of the page :bigwink:
pbnation
Is heat necessary for girth work? Someone on another PE forum said he was having trouble with length, but gained .5 inches in girth in five months. He didn’t warm up. I’ve also seen clamping success without warm ups.
7x5...want 7x6
firegoat
Heat helps with length and girth.
firegoat is fully RETIRED from Thundersplace.
All injuries happen from "too much", or "too much, too soon" or "doing the exercise incorrectly".
Heat makes the difference between gaining quickly or slowly for some guys, or between gaining slowly instead of not at all for others. The ideal penis size is 7.6" BPEL x 5.6" Mid Girth. Basics.... firegoat roll How to use the Search button for best results
airshy
IR Heat has been one of the biggest factors in my gains. When I have not used it or warmed up with heat I can look back and see little to no gains in those periods. Now that winter is here I start getting nervous when that area cools off and it for sure is harder to keep nice and warm after workouts… and it is not that cold where I am at!
3/07 7.75 bpfsl, 4 12/16 midshaft EG
5/08 9.0 bpfsl, 5 10/16 midshaft EG clamped
7/09 8 4/16 BPEL, 6 midshaft EG clamped
8Works
Originally Posted by mgus
According to the info of other posters here, IR will penetrate tissue 10-20 mm (??) - which is straight into the temperature sensitive sperm factory in your nut sack. It will not penetrate cotton cloth though, so keep your boxers high.
What? I have never heard that cotton cloth will block IR. Do we have a good source on this because I put a sock over the heating element of my pad to minimize the temperature of the pad which gets rather hot.
My PE Statistics are here
All times are GMT. The time now is 06:18 PM.