Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Ball zinger - new great (but difficult) idea for boosting voltage

clarification on shooting less

In response to skinneeD, it does seem that I shoot less when I wear the zinger, meaning if I shoot immediately after wearing the zinger for a while. I think it may have to do with the muscles being fatigued. I think the zinger has an effect on the pc, and surrounding muscles. When I wear the zinger and do kegels, I get a different sensation, like it’s harder and easier at the same time. It might have something to do with the electrons crossing over from the zinc to the copper (or vice versa, if anyone knows) stimulating nerves to fire or muscles to contract.

About the semen, I too wish it was thinner so it would shoot further. I remember being disappointed with the explosion because the orgasm was very intense. I don’t know why it would be thicker, maybe the zinger increases the concentration of certain elements, or maybe I didn’t drink enough water or something. I have no idea how the zinger works, but I know it does. I don’t get morning wood anymore, but with the zinger on, the morning wood gets pretty intense.

I’m going to buy the zinc rod from mcmaster.

Can I use the alloy copper rod from mcmaster for the ball zinger, or is the copper tubing better?

ah well...

Dont know about the alloy copper rod. If its an alloy its not pure copper (the tubing probably isnt pure either).

I tried wearing the ball zinger on and off for several hours one day. I wore it at night too but I woke up at around 3:00 am because it was bothering me, so I took it off. I’d say I wore it for about 6 hours total. I masturbated the next day and if anything there was LESS sperm.

I’ll keep trying to experiment with this, but so far I have no results to speak of. I’d like to hear from anyone who had better luck.

"If you build it, she will cum." --Growth of Dreams

I went ahead and bought the alloy 101 copper rod (electronic grade) from mcmaster. It’s 99,99% pure copper.

Looking forward to experience some zingin’…

Sounds great Jambaz, keep us posted on any results- positive or negative.

"If you build it, she will cum." --Growth of Dreams

I just wanted to post an update on the ball zinger. I think the key to the ball zinger is to wear it for an extended amount of time, without taking it off. I wore it for about two weeks straight, and it made a big difference. My libido increased, semen increased, ball size increased, and my flaccid size increased a whole lot. I would have worn it continuously, but my zinc fell out and I lost it. I am going to try to get a hole drilled through the zinc, or maybe make little beads of both the zinc and copper to tie through a string. Either way, I definitely have noticed the difference in wearing the zinger for a long time and not wearing it for a long time.

Does anyone have an original blakoe ring that they are willing to sell?

Hey Anon,
After you lost the zinc piece & stopped wearing it, did your flaccid size, ball size, semen etc revert back to normal? If so, how long did it take to revert back. Sounds like your getting great benefits. I stopped wearing mine after a couple days cause it started to irritate me.

You said earlier that semen decreased (at least initially). So after a while I take it that it eventually increases. How much increase did you get? Was it thinner or thicker? Did you shoot farther?

"If you build it, she will cum." --Growth of Dreams

Yeah, flaccid size, ball size and semen have gone back to normal. It took probably a couple of weeks for them to go back.

As for the semen, it was thick, but it got to the point where there was so much of it it would shoot out pretty hard and far. Also the orgasms were a lot more intense.

Well, I made my first ball zinger. For some reason, I was able to get all the material except for the rubber/latex tube. So I used regular rubber band and superglued it together.

First day: I wore it all day and all night. At first I felt nothing, not even a tingle. about three hours later, my hands and feet felt warm and the veins stood out like I went to a sauna. I felt a little strange too. All this could be psychosomatic though. Anyway, I woke up this morning and did not have the raging hardon that many report. I was disappointed. Plus the rubber band wasnt working so well.

I’m going to have to find rubber tubing today. Hopefully soon.

Question: How tight should the ball zinger be? I’m afraid of making it so tight that the circulation to my ball would get cut off.

Thanks for your help, and I’ll keep everyone posted on my progress.

WHat are ball zingers used for?

<------- You likey?

If you don't take the time to do the PE exercises how do you expect to gain? The fairy godmother of PE?

I made a ball zinger myself (used zinc and red copper).
So after wearing it a couple of hours, I get this green coppperoxide on my balls. :(
Comes off hard, too.

Am I the only one with this problem, or what? Agressive sweat?

This is not good. I will make another one, with stainless steel electrodes and a 1.5 Volt battery.

ps is is night here so my answers (if any) will be delayed…

This really interests me I have to say. What are the life-expectancy of these devices? Would somebody be willing to make me one for an agreed price? I live in the UK. PM me if you would consider it. I’m going to be away for a couple of weeks, so expect a response at the end of August, beginning of September. Thanks!


Is the McMaster zinc a safe alloy? I see no specs on the site?


Originally posted by GiantScale
Is the McMaster zinc a safe alloy? I see no specs on the site?


Assuming you’re using McMaster part #3606 “Zinc Corrosion
Inhibitor Plug” like I am, I looked at the cardboard label around
the brass plug at the end of the rod, and determined that these
are made by Rotometals in San Francisco.

At their website (, they say these
Cor-In (Corrosion Inhibitor) Anodes are special high grade
Zinc (99.99% pure) and meet mil-spec MIL-A-18001.

Hope that helps.


All times are GMT. The time now is 03:41 AM.