Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Looking to buy a cheapish hanger

Looking to buy a cheapish hanger

Ok my routine mainly consists of jelqing some but mainly clamping for girth, now I’ve always wanted to try hanging so does anyone have any recommendations, any help most appreciated

I’m using the Captains Wench I bought it from Monty’s PE weights

Or you could make one yourself there are plenty of threads here on the subject

Try the Hanging forum !

Good luck

Build an AFB hanger or buy a muzzle.

Vacuum hanger.jpg

I think you can guess from the picture what’s the total price of homemade vacuum hanger. :)

Start • 5.94''x4.92''

Now • 6.50''x4.96''

Goal • 7.00''x5.75''

Originally Posted by blink2000

Upto7 is there a thread on how to make a homemade vac hanger?

I second that, looks like by far the most convenient hanger I’ve seen.

Here are some useful threads that helped me grasp the concept:

My homemade vacuum hanger
Successful DIY SuckXtender
Penimaster SuckXtender (posts with pictures: #26, #27, #28, #71)

You can find more by searching for “vacuum hanger” and “suckxtender”.

But it’s really simple to build:

1. Cut off a finger from rubber glove (preferable bigger size, otherwise it likely won’t fit the penis) and cut the finger tip off.
2. Attach it to deodorant cap (which should be a bit bigger than your flaccid).
3. Fasten a cable tie to secure the “sleeve” on the cap. (Note that single cable tie can be used multiple times. You can unhook it using a small screwdriver or similar item.)
4. Add packing tape in shape of letter U which serves as attachment for S hook with weights.

Refer to picture of my hanger posted earlier for easier visualization.


1. Roll the sleeve down like a condom and stretch it over the cap so you can fit your glans in.
2. Glans ridge should be in plane with cap edge, i.e. don’t put your glans all the way in, but just enough so that cap fully covers it.
3. Pull the rolled sleeve from the edge of the cap so it grasps your penis. Once it does, the sleeve should be still unrolled. This can pinch a little.
4. Use your finger to pull out all of excess skin from under the sleeve until only your glans remains in.
5. Unroll the sleeve.

Removing is simple, just roll up the sleeve and use your fingers to pull the glans out of the cap bit by bit.

That’s pretty much it. :) After few sessions of practicing it takes no more than 30 seconds to put on or off.

Start • 5.94''x4.92''

Now • 6.50''x4.96''

Goal • 7.00''x5.75''

Maybe you should start a homemade vac hanger thread.

By the way, thanks for that information.

Originally Posted by blink2000
Maybe you should start a homemade vac hanger thread.

That idea crossed my mind, actually, but I thought it’s not necessary because babbis already did quite a good job. Only difference is vacuum release hole and his design is attached to an extender, but the idea is identical.

Originally Posted by blink2000
By the way, thanks for that information.

Always glad to help. :)

Start • 5.94''x4.92''

Now • 6.50''x4.96''

Goal • 7.00''x5.75''

Those instructions from babbis are buried pretty deep in that thread. That’s too bad for guys trying to find that information (unless they stumble onto this thread).

I may have to try this once I have enough free time to make the device.

Similar Threads 
ThreadStarterForumRepliesLast Post
The AFB HangerPietPenis Hangers8105-17-2018 02:42 PM
Blink2000's Hanging Guideblink2000Penis Hangers5111-08-2015 10:14 AM
Hanging RoutineDickstructionPenis Hangers902-07-2006 03:18 AM

All times are GMT. The time now is 11:56 PM.