Girth measuring question

Today is the last day of my recent 7week girth routine. The last time i did my workout was friday, so today i document my latest official measurements.

I have noticed that my girth measures differently when i do a reverse kegel (the one where u act like you pushing out poop) i get more engorgement and veins pop out. But when i do normal kegels my dick doesnt get much engorgement. Now my questions are as follows:

1) Should i measure after i edge, or just try get an erection? After edging i appear bigger
2) Should i kegel while measuring?
3) If it is a yes to question number 2, should i do reverse or normal kegels.
4) Is it nessesary to measure all Head girth, upper mid girth and base girth? I measure at MEG about 3.5 inches from the base hairline.

Thanks in advance

1. You should measure at least 2 days after/before any exercise’ To have an accurate measurement.

2. You should not kegel’ And you should be 100% erected.

4. Yes it is necessary to measure, in order to track your records’ Other wise you can’t tell how much you gain. Measurement should be taken from Middle, base, and on the lining of your cut’ And if your uncut, you should measure under 1 inch of the head I think. Its very important to keep records’ And remember never fool your self and take an incorrect measurement’ The last thing you want to do is to lie to your self. So take a correct measurement’ In your exercise the details of your measurement, is important beyond imagination’ It can tells you if your exercise suit you or not’ You can tell by the gains, and if you don’t have a record, then the gains are unknown, you know what I mean’ Good luck.

The most important thing is that you measure as consistently as possible. Same spot, same conditions, etc.

I do measure consistantly at the same spot (3.5 inches from the base) and measure without kegeling. My measurement dates are 2 days after a workout. This threat is meant to see how people here vary in measurent techniques and if some measure while kegeling or not

I wait about 10 minutes into an erection ( so it is full )

No kegeling.

Couple days after workout.

I measure base and mseg.

Ok! I just too my official measurements. It took a while because i take some time reaching full erection and i had to measure twice to be sure. So i had to try and use my imagination alot since i dont have access to porn right now. Here are the measurements as of 27/05/2012:

MSEG=5.63”
BEG=5.83”
circumcision scar girth = 5.47”
HEG= 5.00”
Head Width = 1.65”
Shaft Width = 1.89”
BPEL=8.5”

Paper, Card, Ruler, Tape, Glue, Pencil, Scissors:
1— cut a 1cm strip of paper full length of page (30cm?)
2— cut card 3 X 4 cm, lay strip down the middle and trace, then score the card 2mm outside each strip line. The card should fold over the strip and the strip should slide through firmly but not loosely, and DEFINITELY not side-to-side.
******** EXTREMELY IMPORTANT that the card, when folded, has a perfect right-angle so it is straight across so measurements later are accurate ********
3— fold about 2cm of the strip and draw a line on it. Then measure the next full number (my girth is more than 5” around, so I marked it at 5”) after that fold.
4— lay paper flap into card and align with the fold exactly. Put some glue on it and then fold the card down onto it and then tape around the card.. Now “sleeve”.
5— bend strip and come up behind the glued tab and slide it up through the sleeve until the (5”) mark is equal to the fold line.. You will have a 5” girth-ed teardrop shape. Mark precisely where the paper exits the sleeve, and then pull it back out again.
This second mark represent 5”. Though what was in the teardrop measured 5”, I find with every attempt to mark with a pencil while overlapping a strip of paper or ribbon, and some guys use dental floss, it’s just a pain in the neck to manoeuvre sometimes, or, ALL the times. The length of the sleeve may be made longer if you need it (your eyesight might have you otherwise bending down to get a closer look?). But, having two (5”) marks makes this very easy to handle.
6— from the second (5”) mark, begin registering your ruler.. Either 1/8 or 1/16th is up to you. Register as far as you need (I don’t plan on needing more than six and one half inches). Now, re-thread and you are done.

To take an absolute perfectly accurate measurement, keep the strip narrow enough to make like a string, but wide enough for strength. One centimeter is perfect for this. Simply put an object into the loop, and draw the loop till it’s tight. When the two ends of the strip are at sharp right-angles to one-another, what the other end of the sleeve shows is how much is inside the loop.

This is something you can make for no cost, and remake as you need to.

My single photo is too-large to include, but will add it later if anyone wants a picture-instruction of how-to-make this item.

Dude! How the hell is this related to my thread? Stop trolling

LOL, He seems like making a tape measure, I think. Other wise I bet he post it in the wrong thread

Haha yeah maybe, but he should have read the OP first which I highly doubt he did.

TheGr8Leviathan,

I’ll give you that it doesn’t look quite right in this thread but it doesn’t look like trolling to me.

The guy is 3 posts in and posting interesting information. Be nice.

That’s what I was thinking. If anyone searches for ‘Girth measuring question’ it could be a very useful answer for them. Not trolling at all; off topic for the opening post, but on topic for the thread title, and well written for a third post too.

We are not against any one. His trying to help and that’s useful. But there is measuring tape these days. Plus even if its a good post, its totally off the subject. The only good thing he have is his really trying to help, which is grateful.

I second that. It would have been much better for him to share the information on a new ‘suitable’ thread.

You know what I suggest bro :) is to leave this thread. Because we are literally hijacking it :D Now a moderator will come and tell us the same thing. Where is the door I run out first :D