Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

Advantages of BPEL measurement

Advantages of BPEL measurement

I have recently found thunders and just made my first official measurement. 6.5” BPEL. I always thought I was 6” or a touch below, but am very happy with this new measurement. I just wonder, though, what is the consensus on measuring? I mean, for arguments sake, a young maiden gets the most fulfillment from a 7.5” member. If the dude’s rod measures 7” NBPEL and 7.5” BPEL, is this woman going to be getting that full 7.5” or is she going to be left short, so to speak. Just a thought.

The bone pressed measurement is not for her, it’s for you. It gives you a constant datum point for measuring no matter how thick your fat pad is.

In order for them to be of any use, measurements must be taken under circumstances as consistent as they can be.

Since coming here I have learned a lot about my dick, particularly how moody the little bastard can be! It strikes me that N/BPEL measurements ultimately depend upon erection quality- and THAT depends on so much more such as general and momentary interest level, general and momentary physical condition level, distractions, etcetera. My initial measurements were done almost 3 weeks after I began because I wasn’t experiencing a sufficiently high quality erection or I wasn’t responding well to the measuring process or I got distracted.

I cannot guarantee a consistent degree of hardness. Hell, what happens if I pop a little blue pill and get the hard-on of a lifetime?

So while I happily note changes in BPEL on my tally stick, and will claim that number as my measured size, I find myself reaching for my BPFSL [Bone Pressed Flaccid Stretched Length] tally stick and stretching to the same subjective discomfort level [medium “Owww!”- not quite “Son of a Bitch!”]. BPFSL is the one measurement that I know I can compile with the minimum of variables- do my PE and when it’s over, whip out the tally stick and see where it’s at.

NBPEL? Unless you have a well placed birth mark, how do you know you are consistent?

Just my opinion as to what works for me as benchmarking.


WE are the 99% 'WE are the people you depend on; we cook your meals, we haul your trash, we connect your calls. We drive your ambulances. We guard you while you sleep. Don't f&ck with us'-- Madame DeFarge

"Rope trades @$10 a yard. I wonder if they even know that?"- Capitalist

I agree. Track BPEL and BPFSL for length. Between them you’ll have a good idea of what is going on.

As for useful length when screwing, the general consensus seems to be that it’s somewhere between BP and NBP because the fat pad compresses.

Additionally

Since beginning my quest in earnest, I have found a correlation between BPFSL and BPEL- meaning that while they definitely do not move in lock step, whenever I note a substantive increase in BPFSL, there will generally be an increase in BPEL following shortly [poor choice of word]- and generally speaking, my BPEL, while initially >~.5” less than my BPFSL, has moved to within <~.25” of my BPFSL, a difference that seems reasonably attributable to length compression due to girth expansion.

What does this mean to me?

Others here far wiser and more experienced in the ways of PE than I have positted that initial gains [aka the “newbie pop”] may be as much a matter of improved erectile quality and measurement accuracy as they are actual penile size increase.

My own experience would seem to bear this out.

While not having taken any accurate measurements as a younger man [I voted for Ronnie once- and almost twice], I do definitely recall that what measurments I did take were substantially larger than my pre- PE inches noted here. This would seem to be born out by supersizeit’s noting of size differentials at different life stages.

Why do I come back to this?

As a pure measurement tool, I echo hobby’s sentiment- with my own corollary.

First and foremost establish your baseline inches [or cms.] - in order of importance

BPFSL- minimum fudge factor, just keep the ruler tucked tight against the shaft, stand like a two legged creature not a four and push until the discomfort tells you that you are at the end.

This measurement is your “true” length, which really cannot be influenced by much- other than being done pre or post PE/ warm- up [in other words, once you figure the basics of determining dick dimensionality [I do so love alliteration], you can only fuck up BPFSL if you actually try to fuck it up.

BPEL- Then get some good wood going, take it to the edge and do the same- this is your “interest influenced” length. As mentioned above, even if you are rock solid on your manhood measurement methodolgy [there goes that alliterative addiction again] [oops!], a cold breeze - or the memory of your gran in her panties- can queer your results objective accuracy. This is the number that indicates your capacity to access your “true” BPFSL measurement [for your partners’ pleasure, as they say]

NBEL- useless IMHO, but if it works for you, I would think that as long as you can assure longitudinal consistency, then rock on.
Me? I’m not that smart.
If I know that my NBPEL can range from .4- .7” depending on my edema level [I am one water logged sumbitch- can you say ‘thank you northen european genes with me?], simple pressure approximating my average coital bump can tell me how much impact said fat pad will have.

BUT- I personally dig a bunch of positions that don’t really engage the fat pad, and in those I can feel the CDS thingy, so, is the NBPEL really relevant for me?

Should I state as a caveat:

"Baby, if you want to go at it in mish, I’m running about 6.6”, unless you toss my salad, in which case I will run above 6.75”, but if I take you in quarter spoon with one leg under and the other turned over so that you are laying on your side, I will be able to graze the 7.2” mark as I will be able to avoid my porcine fat pad”?

Not criticizing, just spitballing as I contemplate my new obsession.
And I did finsih a bottle with dinner, so if I wax verbose… .


WE are the 99% 'WE are the people you depend on; we cook your meals, we haul your trash, we connect your calls. We drive your ambulances. We guard you while you sleep. Don't f&ck with us'-- Madame DeFarge

"Rope trades @$10 a yard. I wonder if they even know that?"- Capitalist

Originally Posted by hobby
I agree. Track BPEL and BPFSL for length. Between them you’ll have a good idea of what is going on.

As for useful length when screwing, the general consensus seems to be that it’s somewhere between BP and NBP because the fat pad compresses.

The fat pad compresses, but I am not sure how much. What you said is correct, right on the money.

Top
Similar Threads 
ThreadStarterForumRepliesLast Post
Measurement method and good record keepingsheLovesItPenis Enlargement002-28-2005 04:56 AM
Learn how to take a good starting measurementVegasGuyPenis Enlargement Basics510-06-2004 04:07 AM
BPEL measurement = cheating yourself?a529612Penis Enlargement911-03-2003 12:16 AM
Cellular Growth Hypothesisi_will_get_8_inchesPenis Enlargement2806-04-2003 02:51 AM
Which way is a more accurate measurement BPEL or FSBPL?mike2002Penis Enlargement702-14-2003 05:07 PM

All times are GMT. The time now is 11:18 PM.