I have reached my goals

Congrats.. Keep it up.

Ted Baker

Lucky son of a gun. Good job!

Thanks ck.

My wife and I have been noticing razor blade like cuts on my penis the morning after PEing. I get them where my first clamp is positioned and where the second clamp is positioned. We never had this problem until my recent gains. After third and final set of clamping, my penis is very engorged and we have to remove the clamp by sliding the open clamp off to the side of my penis carefully because it is holding my penis tightly even when opened.

If you look at pic Clamp-1, you will see a raised seam where I am pointing to. Once your penis becomes pipe hard in the clamp, the slightest seam can act like a razor when sliding the clamp off. All of my clamps have this, and one of them has a recessed seam which acts the same as the raised seam, like a razor blade.

Look at pic Clamp-2 and if you look carefully, you can see that I have smoothed that area with 400 grit wet/dry sand paper. I also did the corners being careful not to ruin the integrity of the clamp. I then took a cotton cloth and buffed the area. Problem fixed, no more cuts.

I have included pic Clamp-3 to show how I prepare my clamps. I cut .75 inch strips of mouse pad. I then put a dab of Marine cement on the inside diameter just under and right before the teeth arm and on the ratchet area about .25 before the opening. Do not glue the pad on the hinged area because the clamp will become uncomfortable when it is tighten on the penis. I use marine cement because it dries within 15 minutes and is water proof so that I can clamp while showering. I will now include sanding the inside teeth arm to the preparation of my new clamps. A couple other important things, if you notice the on my clamps, the rubber side of the mouse pad is glued to the clamp and the fabric side is what goes around the penis. I once glued the fabric side to the clamp and the rubber side gave me a sore kind of like a burn at the base. Also, cut the strip a little long before gluing to the clamp. After the glue is dried, trim the padding .25 of an inch longer so the padding over laps on the teeth arm and is .25 longer on the ratchet side. If you trim the padding right at the beginning of teeth arm and at the opening you will get the hell pinched out of your penis when you tighten the clamp to the last couple of clicks.

Hope this helps.

Pics are here:
tntjockey - I have reached my goals

Where are the pics ?

I don’t know tnt but you can’t post dick pics in Main remember…

I didn’t, they are just pictures of my clamps.

Try it again tnt. Browse, then click upload and make sure the attachment is shown after you click upload. If its not it would give a message like your file is too big or something.

Fair enough- give it another shot..

Can a Moderator move these pics to my post 64? Thanks

I put a link to your pics post in your post #64 tnt.

Oooo racing green - classy..:up:

Thanks Thunder.

Okay guys, well my girth as of today is still 5.6 and my EBPL is at 7.5. Nothing gained or nothing lost, which bothers me a bit. Tomorrow is the first day of my 2 week break and I am really starting to think 2 weeks off may be pushing the envelop. Since I have gained nothing nor lost anything, could it mean that I have cemented my gains? It could also mean that I could loose gains during the next 2 weeks.

By the way, my wife read this thread and she says I left so much out, like drinking a lot of water just before and during PEing. I told her, urinating just after PEing was like a mini warm down. Not sure if it is, but urine does come out warm and maybe it is beneficial warming down from the inside out. So she thinks I should have posted that. The rest of the things that I left out are things that have already posted here at Thunders.

I will not look back and continue this schedule to see if this is in-fact working for me. I will keep you posted.

Hellooooooooo Mrs tnt…;)