Thunder's Place

The big penis and mens' sexual health source, increasing penis size around the world.

How to make your own tugger, with photo.

How to make your own tugger, with photo.

Materials:
1.PET Soda/water bottle, it must have a narrow tapered neck so 250/500ml bottles are best. A cap with a drinking nozzle is best as it is a cone shape.

2.Silicon sealant (food grade if you are worried).

3.Piece of string, shoelace, cord about 1 foot, strong enough to take weights and thick enough to make a good knot.

4.Weights or ADS attachment.

Method:

1.Take the movable nozzle off the cap (you may need a pliers).

2.Bore a small hole in the middle of the cap just large enough to fit the string through.

3.Feed the string through the hole and tie a few knots in the end so it cannot be pulled through the cap from the outside. Cut off any excess frayed string from where the knots are. Pull the string firmly so the knot is lodged tight in the inside of the cap.

4.Fill the inside of the cap with silicon sealant and smooth it into a slightly dished shape at the bottom where the glans will fit. Smoothing can be done with an old knife or wearing latex gloves or a plastic bag on your hand. Now cover the outside of the cap in a thin layer of silicon. The nozzled cap has ridges but is roughly a cone shape so try to smooth the silicon into the gaps of the ridges to make a cone shape. A regular cap will be harder to form into a cone shape. Leave it to set a while. After it has set a bit put another layer on the outside and try to smooth it out. Make sure the entire cap is covered in silicon especially the rough edge at the bottom of the cap. Let it cure for 24hrs, you don’t want it stuck on you for good!

5.Cut the neck from the bottle as close as you can to the top, best done with a hacksaw or serrated knife as a blade can slip or cut unevenly. Now cut it about 1.5” down the bottle so you end up with a cone shape, cut more than 1.5” if you wish as it can always be trimmed later. Now cover the inside of this cone with a thin layer of silicon. Let it cure for 24hrs.

6.Tie a loop in the end of the string. The loop must be big enough for the cap and outer cone to go through. It must not be a noose so the best way to tie is to fold the string back on itself about 4-5” and then tie a normal knot with the doubled up string to form a loop.

7.Feed the outer cone onto the string, then feed the weights onto the string and pass the tugger and outer cone through the loop so the weights are held in place without need for s-hooks. It could also be attached to an ADS style leg attachment.

8.Peel back the foreskin and push the tugger cone firmly against the glans. Roll the foreskin back up onto the tugger cone.

9.Now push the outer cone into place over the foreskin and gently let the weights down.

Pictures can be seen on the commercial tugger site. If the cones don’t fit right you can add more silicon. A larger bottle can be used, it just means adding a thick layer of silicon inside the cone. I can comfortably hang 8lb with mine. This is a vacuum device so blisters are possible at higher weights. I have used mine for an hour at a time, there is no worry of loss of circulation to the glans but the foreskin may need blood especially at higher weights. I take the outer cone off every 20mins to ensure it has blood.

Attached Images
tugger.jpg
(36.7 KB, 1761 views)

The "average size" is usually over-estimated. Small guys don't take part in surveys and big guys jump at the chance.

Girl claims she had a huge ex? Stick a spider in the bathroom or a mouse in the kitchen and when she comes out screaming ask her how big the spider/mouse was...


Last edited by twatteaser : 05-27-2004 at . Reason: Added spaces for easier reading.

Cool, trigger.

I’ve been working on a tugger myself lately (for restoring foreskin; not foremost as a PE ADS), and luck has it I have an item at homem, which is pretty much identical to the TLC inner cone: a conical toothpaste (“Denivit” in Euroland) cap; exactly the same base diameter (33mm) as the standard TLC. Shave off some base with sandpaper and you have the mini TLC (30mm). TLC probably used the Denivit cap for their mold :nodding:

Once you have this cone, You can probably figure out for yourselves how to make a tugger out of it.

Still working on (perfecting) the outer cone/thingy. A supple leather covered section of a plastic funnel is my best bet yet. Only I need to find the funnel…

EDIT: One thing, trigger… You’re using aquarium silicone, are you? I don’t think regular hardware store silicone is healthy to use on your skin.

I’ll keep and eye out for that toothpaste. I mentioned about food grade/aquarium silicon at the start, I personally wouldn’t be too worried about it, I have a plastic strap on a watch which probably isn’t foodgrade! The glans is a thin skin though so it is probably better safe than sorry.

The transparent silicon is great as you can see how thick a layer you have put on the cap, also a transparent outer cone shows where you can add more silicon on the inside because you can see where the pressure is on the foreskin. You want a pretty even pressure on it.


The "average size" is usually over-estimated. Small guys don't take part in surveys and big guys jump at the chance.

Girl claims she had a huge ex? Stick a spider in the bathroom or a mouse in the kitchen and when she comes out screaming ask her how big the spider/mouse was...

Alright, trigger… I must have overloked your mention; got a fine hangover this morning :)

I was waiting a post of how to make a tugger…

Thanks trigger! :)


CURRENT 7.1" x 5" (8" stretched) ----> GOAL 8" x 6" NBP

Semen retentum venenum est

Can you post pics of the components you used before you made them?

Yes, I’d like to see those as well! Very slick idea trigger. Hanging 8 lbs with little to no problems is just what I’ve been looking for.

ineed9

I don’t know when I can get hold of a camera again. If you need further descriptions I will tell you. I am up to 11lb with it no with no problems. I hung 11lb for about 40mins, the glans looked very odd afterwards, very bumpy and looked like blisters, got an erection and it was back to normal. Over on MOS somebody did get blisters using it as an ADS so be careful.


The "average size" is usually over-estimated. Small guys don't take part in surveys and big guys jump at the chance.

Girl claims she had a huge ex? Stick a spider in the bathroom or a mouse in the kitchen and when she comes out screaming ask her how big the spider/mouse was...

Can you maybe find pictures of the components online?

trigger,

How much extra skin does one need to use the tugger? I’m cut so not sure if it would work or not. I do however have some extra skin I’m not using due to pumping for 5 months now. Are you cut? or does it really matter that much? 11 lbs…WoW!! way to go!

Thanks for the heads up about the blisters.

ineed9

any progress reports/comments please?

Top
Similar Threads 
ThreadStarterForumRepliesLast Post
Can naturally bigger guys make bigger gains?grindylowPenis Enlargement1305-30-2009 01:53 AM
To make a pump?jacket67Penis Pumps111-07-2003 06:23 PM

All times are GMT. The time now is 11:53 AM.